Page 41 / 52 Scroll up to view Page 36 - 40
78
Advanced Setup Method
Advanced Setup Method
79
section
2
1
3
4
5
6
7
Traffic Statistics
This page shows the WAN outbound traffic statistics of all the Diffserv
forwarding groups in the last 12 hours (automatically updated every 5
mins).
DDNS
Edit Traffic Class
This page is for user to specify a classify rule.
Rule Name:
Assign a Name to the rule.
Traffic Type:
Choose a Traffic type foe the rule, or click on
“Advanced Config” for more advanced options.
Map to Forwarding
Group:
Choose which QOS group you wish to have the rule mapped
to, which determines how much bandwidth is to be allocated with this
rule.
Direct to VC:
Choose which ATM connection you wish to have the
rule mapped to. The default setting of “By Routing” should be used.
Page 42 / 52
80
Advanced Setup Method
Advanced Setup Method
81
section
2
1
3
4
5
6
7
Firmware Upgrade
Use this screen to update the firmware or user interface to the latest
versions.
Download the file to your hard drive from the Belkin web site or from
another source. Then click Browse... to find the file on your computer.
Select the firmware file and click “Open”. Click “Save Settings” to
start the upgrade process.
With a DDNS (Dynamic DNS) connection you can host your own web
site, email server, FTP site and more at your own location even if you
have a dynamic IP address.
Parameter Description
Dynamic DNS:
Enable or disable the DDNS function.
Provider:
Select which provider you wish to use for your DDNS
service, either DynDNS or TZO.
Tools
Use the Tools menu to back up the current settings, to restore
previously saved settings, or to restore the factory default settings.
Configuration Tools
Check Backup Router Configuration and click “NEXT” to save your
VoIP Router’s configuration to a file named “backup.cfg” on your PC.
You can then check Restore from saved configuration file (backup.cfg)
to restore the saved backup configuration file.
To restore the factory settings, check Restore router to Factory
Defaults and click “NEXT.” You will be asked to confirm your decision.
Click “APPLY” to proceed, or “CANCEL” to go back.
Page 43 / 52
82
Advanced Setup Method
Advanced Setup Method
83
section
2
1
3
4
5
6
7
The security log may be saved to a file by clicking “Save” and
choosing a location.
The following items are included on the Status screen:
Parameter Description
Internet:
Displays WAN connection type and status. Release Click on
this button to disconnect from the WAN. Renew Click on this button
to establish a connection to the WAN.
Gateway:
Displays system IP settings, as well as DHCP Server and
Firewall status.
Information:
Displays the number of attached clients, the firmware
versions, the physical MAC address for each media interface and for
the VoIP Router, as well as the hardware version and serial number.
ATM PVC:
Displays ATM connection type and status.
Save:
Click on this button to save the security log file.
Clear:
Click on this button to delete the access log.
Refresh:
Click on this button to refresh the screen.
Reset
Perform a reset from this page.
Should your unit become unresponsive for any reason, you can simply
perform a reset from this page. Performing a reset will reboot the
device. Your configuration settings will remain the same.
Status
The Status screen displays WAN/LAN connection status, firmware and
hardware version numbers, as well as information on DHCP clients
connected to your network.
Page 44 / 52
85
84
Advanced Setup Method
Appendices
85
section
2
1
3
4
5
6
7
DHCP Client LOG
DHCP Client Log:
Displays information on DHCP clients on your
network.
Security LOG
Security Log:
Displays information about attempts to access ports
and addresses. Also displays information about your ADSL connection
such as Login failures, disconnections and etc.
Appendix A1 Troubleshooting
After completing hardware setup by connecting all your network
devices, you should automatically be able to connect to the VoIP
ADSL Wireless Router by entering 10.1.1.1 into your Internet browsers
address bar.
Should this not work please first determine how your ISP issues
your IP address. Many ISPs issue these numbers automatically using
Dynamic Host Configuration Protocol (DHCP). Other ISPs provide
a static IP address and associated numbers, which you must enter
manually. How your ISP assigns your IP address determines how you
may need to change the configuration of your computer as per the
steps below.
TCP/IP Configuration
To access the Internet through the VoIP Router, you must configure
the network settings of the computers on your LAN to use the same IP
subnet as the VoIP Router. The default network settings for the ADSL
Router are:
IP Address:
10.1.1.1 Subnet Mask: 255.255.255.0
Note:
These settings can be changed to fit your network requirements,
but you must first configure at least one computer to access the VoIP
Router’s web configuration interface in order to make the required
changes.
Configuring Your Computer in Windows 2000
DHCP IP Configuration
1.
On the Windows desktop, click Start/Settings/Network and Dial-
Up Connections.
2.
Click the icon that corresponds to the connection to your VoIP
Router.
3.
The connection status screen will open. Click Properties.
Page 45 / 52
86
Appendices
Appendices
87
section
2
1
3
4
5
6
7
Manual IP Configuration
1.
Follow steps 1-4 in “DHCP IP Configuration” on the previous
page.
2.
Select “Use the following IP address.” Enter an IP address based
on the default network
10.1.1.x (where x is between 2 and 254), use
255.255.255.0 for the subnet mask and the IP address of the
VoIP Router 10.1.1.1 for the Default gateway field.
3.
Select “Use the following DNS server addresses.”
4.
Enter the IP address for the VoIP Router in the Preferred DNS
server field. This automatically relays DNS requests to the DNS
server(s) provided by your ISP. also, add a specific DNS server of
your ISP into the Alternate DNS Server field and click OK to close
the dialog boxes.
5.
Record the configured information in the following table.
TCP/IP Configuration Setting
IP Address
____.____.____.____
Subnet Mask
____.____.____.____
Default Gateway
____.____.____.____
Preferred DNS Server
____.____.____.____
Alternate DNS Server
____.____.____.____
Disable HTTP Proxy
You need to verify that the “HTTP Proxy” feature of your web browser
is disabled. This is so that your browser can view the VoIP Router’s
HTML configuration pages.
1.
Open control panel.
2.
Open internet options
3.
Go to the connections tab and click on the LAN settings button.
4.
Ensure that NOTHING is ticked on this screen and click ok.
5.
On the connections tab, make sure that there are no dial up
connections, select the “Never dial a connection” radio button.
1.
Double-click Internet Protocol (TCP/IP).
2.
If “Obtain an IP address automatically” and “Obtain DNS server
address automatically” are already selected, your computer is
already configured for DHCP. If not, select these options and then
click ok and then ok again, or click Cancel to close each window.

Rate

4 / 5 based on 1 vote.

Popular iiNet Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top