User Manual

Aolynk DR811/DR814 ADSL2+Broadband Router

4 Web-based Management

23

●

Click

WAN Setup

in the Main menu and choose the

WAN

tab in the Main Frame

to open the WAN connection configuration page, and then click the

label to open the route configuration page.

●

Click

LAN Setup

in the Main menu and choose the

LAN

tab in the Main Frame to

open the LAN configuration page, and then click the

label to open the

route configuration page.

●

Click

Status

in the Main menu and choose the

Status

tab in the Main Frame to

open the status page, and then click the

label to open the route

configuration page.

Figure 4-10

Routes configuration

This page allows you to:

●

View the information about existing routes.

●

Edit a route present in the route list.

●

Add a new route to the DNS relay's list.

●

Delete a present route.

This page lists the following information about existing routes:

●

Whether the route is valid

or invalid

.

●

Destination IP address.

●

Gateway address.

●

Netmask.

●

Whether the route is advertised via RIP (true or false)

To edit the destination address, gateway address, netmask and advertise status of a

route, click in the relevant text box, update the information then click the

button.

To edit the cost or interface settings for the route, click the

label to

open the web page

advanced setting

.

User Manual

Aolynk DR811/DR814 ADSL2+Broadband Router

4 Web-based Management

24

Figure 4-11

Advanced setting of routes

Update the relevant values of route options, and then click the

button.

To delete an existing route item, check the corresponding check box

and click the

button.

To add a new route item, click the

label to open the web page

IP

V4Route

. Enter the values of route options, and then click the

button. Click the

button to abort this action and return to the route configuration page.

Figure 4-12

Create routes

User Manual

Aolynk DR811/DR814 ADSL2+Broadband Router

4 Web-based Management

25

&

Note:

For DHCP or fixed IP service, the address of the next hop must be entered in the

Gateway

box (the box must not be left blank), while Interface can be the default

None

or any other value. For other services (i.e. IPoA, PPPoA, PPPoE), either

Interface

or

Gateway

must be specified with a value; if both of them are configured, only

Interface

takes effect.

4.7 Security Interface

Click

Security

in the Main menu and select the

Interface

tab in the Main Frame to

open the

Security Interface Configuration

page.

Figure 4-13

Security interface

This page allows you to:

●

Enable/disable the security.

●

Enable/disable the firewall.

●

Enable/disable the intrusion detection.

●

Assign the security level.

●

Add/delete a security interface.

●

Enable/disable NAT to internal interfaces.

●

NAT configuration.

To enable/disable the firewall, click the radio button

labeled

Enabled/Disabled

corresponding to

Firewall

, then click the

button.

To enable/disable the intrusion detection, click the radio button

labeled

Enabled/Disabled

corresponding

to

I

ntrusion

Detection

,

then

click

the

button.

User Manual

Aolynk DR811/DR814 ADSL2+Broadband Router

4 Web-based Management

26

To enable/disable the security, click the radio button

labeled

Enabled/Disabled

corresponding to

Security

, then click the

button.

&

Note:

Firewall, intrusion detection and NAT can only be enabled if security is enabled.

Firewall, intrusion detection and NAT must be disabled if security is disabled.

The security level drop-down list contains entries defined as below, in which

None

level

indicates that Internet users are not allowed to access the intranet,

High

level indicates

that Internet users have part of the intranet services-access authority,

medium

level

indicates even higher authority, and

Low

level indicates the highest authority. To set the

proper security level, position the cursor over the entry and left-click to select it, and

then click the

button.

&

Note:

Firewall must be enabled before security level can be configured.

To add a new security interface, click the

label to open the web page

Add

Interface

. Make sure that you have created a virtual interface before doing so. Refer to

4.4

LAN Setting for the way to create a virtual interface.

Figure 4-14

Security

–

add interface

User Manual

Aolynk DR811/DR814 ADSL2+Broadband Router

4 Web-based Management

27

Click on the

Name

drop-down list and select the LAN service that you want to base

your security interface on. Only IP interfaces that have not been assigned a security

type are displayed.

Click on the

Interface Type

drop-down list and specify what kind of interface it is

depending on, that is, how it connects to the network: external, internal or DMZ.

Click the

button. The Security page is displayed, The

Security Interfaces

table

displays information about each existing security interface, including the interface that

you have just configured.

To delete a present security interface, click the corresponding

label to

open the web page

Delete Interface

, and click the

button.

Figure 4-15

Security

–

delete interface

If the NAT is currently disabled, you may click the

button to enable it. If the NAT is currently

enabled, you may click the

button to

disable it.

To perform advanced NAT configuration, click the

label to

open the web page

Advanced NAT Configuration

. If needed, modify the

Global

Address Pools

and

Reserved Mappings

configurations.