Manual Ver1.0

- 6 -

Rear Panel

The connectors located at the rear panel have the following functions.

M404/M405

Interface

Function

Switch(Push Button)

Power switch on/off

Power

Connects to the power adapter cable

Reset

Resets unit’s configuration to factory default

USB

USB connection: Connects to your PC’s USB 1.1/2.0

port

Ethernet

RJ-45 connector: Connects to your PC's Ethernet port,

or to the uplink port on your LAN's hub/switch

Line

RJ-11 connector: Connects to your ADSL line

Connecting the Hardware

Connect the M404/M405 to the phone jack, the power outlet, and your computer or network.

WARNING

Before you begin, turn the power off for all devices.

These include your

computer(s), your LAN hub/switch (if applicable), and the M404/M405.

Step 1. Connect the ADSL cable and optional telephone

Connect one end of the phone cable to the RJ-11 connector on the rear panel of the M404/M405.

Connect the other end to the ADSL outlet provided by your service provider (normally MODEM

port of the included splitter).

Step 2. Connect the Ethernet cable

Connect one end of the Ethernet cable to the RJ-45 connectors on the rear panel of the M404/M405

and connect the other end to your PC’s network adaptor (NIC). If you are connecting a LAN to the

Master series, attach one end of the Ethernet cable to a regular hub port and the other end to the

LAN port on the M404/M405.

Manual Ver1.0

- 7 -

Step 3. Attach the power connector

Connect the AC power adapter to the power connector on the M404/M405 and plug in the adapter

to a wall outlet or power extension.

Step 4. Turn on the M404/M405 and power up your systems

Press the Power switch on the back panel of the M404/M405 to the ON position.

Boot up your computer(s) and any LAN devices such as hubs or switches.

Step 5. Configure the M404/M405 through the WEB interface

Please refer to Chapter 3.

Step 6. Save the configurations and Reboot

Save the changes you made on the M404/M405 and it will automatically reboot to make the settings

permanent.

Manual Ver1.0

- 8 -

3. Configuration

3.1 - Setup

°

Connect your M404/M405 and PC with an RJ-45 Ethernet cable.

°

Turn on the M404/M405.

°

The default IP address of M404/M405 is 192.168.1.254.

3.2 - Establish the Connection

°

Enter the IP address (default: 192.168.1.254) of M404/M405 in the address line of

your web browser.

°

A Dialogue Box will pop up to request the user to login. (Figure 1)

Figure 1. Login dialogue box

°

Please enter the management username/password into the fields then click on the

OK

button (Please contact your ISP for login information).

°

If the authentication is valid, the main page will be displayed on the screen.

(Figure 2)

Manual Ver1.0

- 9 -

Figure 2. M404/M405 Home Page

Manual Ver1.0

- 10 -

4. Quick Setup

The system administrator can configure the M404/M405 remotely or locally via a Web

Browser. Network configuration needs to be planned and decided before starting the

configuration procedure.

Quick Setup allows system administrator to select the appropriate operation mode and

configure the corresponding settings step by step to create a connection. The following

operation modes are supported under Quick Setup:

°

PPP over Ethernet (PPPoE)

°

PPP over ATM (PPPoA)

°

MER (MAC Encapsulation Routing)

°

IPoA (IP over ATM)

°

Bridging

4.1 - PPP over Ethernet (PPPoE) Configuration

Click on “Quick Setup” in the left frame and follow the steps below to create a PPP

over Ethernet (PPPoE) connection.

Here you can either select DSL Autoconnect (Modem will attempt to find the correct

VPI/VCI settings) or Uncheck the box to manually input the VPI/VCI settings.

Figure 3. Quick Setup – ATM PVC