Soniq CWR150NS Router Manual PDF (Setup & Configuration Guide)

Page 36 / 90 Scroll up to view Page 31 - 35

- 35 -

Field

Description

Table

.

Delete Selected

Select a row in the

DHCP Static IP Table

, then

click it, this row is deleted.

Reset

Click it to refresh this page.

DHCP Static IP Table

It shows the assigned IP address based on the

MAC address.

3.4.2

WAN

Choose

Network

>

WAN

. The

WAN

page that is displayed contains

WAN

,

ATM

Setting

and

ADSL Setting

.

3.4.2.1 WAN

Click

WAN

in the left pane, the page shown in the following figure appears.

In this page, you can configure WAN interface of your router.

Page 37 / 90

- 36 -

The following table describes the parameters of this page:

Field

Description

Default Route Selection

You can select

Auto

or

Specified

.

VPI

The virtual path between two points in an

ATM network, ranging from 0 to 255.

VCI

The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (1 to

31 are reserved for known protocols)

Encapsulation

You can choose

LLC

and

VC-Mux

.

Channel Mode

You can choose

1483 Bridged

,

1483 MER

,

PPPoE

,

PPPoA

,

1483 Routed

or

IPoA

.

Enable NAPT

Select it to enable Network Address Port

Translation (NAPT) function. If you do not

select it and you want to access the Internet

normally, you must add a route on the uplink

equipment. Otherwise, the access to the

Internet fails. Normally, it is enabled.

Enabel IGMP

You can enable or disable Internet Group

Management Protocol (IGMP) function.

PPP Settings

User Name

Enter the correct user name for PPP dial-up,

which is provided by your ISP.

Password

Enter the correct password for PPP dial-up,

which is provided by your ISP.

Type

You can choose

Continuous

,

Connect on

Demand

, or

Manual

.

Idle Time (min)

If set the type to

Connect on Demand

, you

need to enter the idle timeout time. Within the

preset minutes, if the router does not detect

the flow of the user continuously, the router

automatically

disconnects

the

PPPoE

connection.

WAN IP Settings

Type

You can choose

Fixed IP

or

DHCP

.

Page 38 / 90

- 37 -

Field

Description

°

If select

Fixed IP

, you should enter the

local IP address, remote IP address and

subnet mask.

°

If select

DHCP

, the router is a DHCP

client, the WAN IP address is assigned

by the remote DHCP server.

Local IP Address

Enter the IP address of WAN interface

provided by your ISP.

Netmask

Enter the subnet mask of the local IP

address.

Unnumbered

Select

this

checkbox

to

enable

IP

unnumbered function.

Add

After configuring the parameters of this page,

click it to add a new PVC into the

Current

ATM VC Table

.

Modify

Select a PVC in the

Current ATM VC Table

,

then modify the parameters of this PVC. After

finishing, click it to apply the settings of this

PVC.

Current ATM VC Table

This table shows the existed PVCs. It shows

the interface name, channel mode, VPI/VCI,

encapsulation

mode,

local

IP

address,

remote IP address and other information. The

maximum item of this table is eight.

Click

in the

PPPoE

mode, the page shown in the following figure appears. In

this page, you can configure parameters of this PPPoE PVC.

Page 39 / 90

- 38 -

The following table describes the parameters and buttons of this page:

Field

Description

Protocol

It displays the protocol type used for this WAN

connection.

ATM VCC

The ATM virtual circuit connection assigned for

this PPP interface (VPI/VCI).

Login Name

The user name provided by your ISP.

Password

The password provided by your ISP.

Authentication Method

You can choose

AUTO

,

CHAP

, or

PAP

.

Connection Type

You can choose

Continuous

,

Connect on

Demand

, or

Manual

.

Page 40 / 90

- 39 -

Field

Description

Idle Time (s)

If choose

Connect on Demand

, you need to

enter the idle timeout time. Within the preset

minutes, if the router does not detect the flow of

the user continuously, the router automatically

disconnects the PPPoE connection.

Bridge

You can select

Bridged Ethernet

,

Bridged

PPPoE

, or

Disable Bridge

.

AC-Name

The accessed equipment type.

Service-Name

The service name.

802.1q

You can select

Disable

or

Enable

. After enable

it, you need to enter the VLAN ID. The value

ranges from 1 to 4095.

Apply Changes

Click it to save the settings of this page

temporarily.

Return

Click it to return to the

Channel Configuration

page.

Reset

Click it to refresh this page.

Source Mac address

The MAC address you want to clone.

MAC Clone

Click it to enable the MAC Clone function with

the MAC address that is configured.

3.4.2.2 ATM Setting

Click

ATM Setting

in the left pane, the page shown in the following figure appears.

In this page, you can configure the parameters of the ATM, including QoS, PCR,

CDVT, SCR and MBS.

Rate

Popular Soniq Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share