1. Home
    2. /
  2. Manuals
    3. /
  3. SnapGear
    4. /
  4. SG565
    5. /
  5. 3
Page 11 / 249 Scroll up to view Page 6 - 10
Introduction
6
Your CyberGuard Gateway Appliance
CyberGuard gateway appliances include:
•
SG300
•
SG530
•
SG550
•
SG560
•
SG565
•
SG570
•
SG575
•
SG580
The following items are included with your CyberGuard SG appliance:
•
Power adaptor
•
Installation CD
•
Printed Quick Install guide
•
Cabling including
o
1 normal
straight through
UTP cable (blue color).
o
1
crossover
UTP cable (either gray or red color)
Note
The SG300 model includes two blue
straight through
UTP cables.
Front panel LEDs
The front and rear panels contain LEDs indicating status.
An example of the front panel
LEDs are illustrated in the following figure and detailed in the following table.
Figure 1-2
Page 12 / 249
Introduction
7
Note
Not all the LEDs described below are present on all CyberGuard SG appliance models.
Also, labels vary from model to model.
Label
Activity
Description
Power
On
Power is supplied to the CyberGuard SG appliance
Flashing
The CyberGuard SG appliance is operating correctly
Heart Beat
On
If this LED is on and not flashing, an operating error
has occurred
Error! Reference source not found.
LAN Activity
Flashing
Network traffic on the LAN network interface
WAN Activity
Flashing
Network traffic on the Internet network interface
WLAN
Flashing
Network traffic on the Wireless network interface
DMZ Activity
Flashing
Network traffic on the DMZ network interface
Serial Activity
Flashing
For either of the CyberGuard SG appliance COM
ports, these LEDs indicate receive and transmit data
HA
On
Reserved to indicate failover to a backup device
(available in a future firmware release)
Online
On
An Internet connection has been established
VPN
On
Virtual Private Networking is enabled
Online
On
An Internet connection has been established
Note
If
Heart Beat
does not begin flashing shortly after power is supplied, refer to Appendix E,
Recovering From a Failed Upgrade.
Rear panel
The rear panel contains network and serial connector ports, the
Reset
/
Erase
button and
power inlet.
If network status LEDs are present, the lower or left LED indicates the
link
condition, where a cable is connected correctly to another device and the upper or right
LED indicates
network
activity
.
Page 13 / 249
Introduction
8
CyberGuard Gateway Appliance Features
Internet link features
•
10/100baseT Ethernet port
•
Serial port
•
Front panel serial status LEDs (for TX/RX)
•
Online status LEDs (for Internet/VPN)
•
Rear panel Ethernet link and activity status LEDs
LAN link features
•
10/100BaseT LAN port
(SG530, SG550)
•
10/100BaseT 4 port LAN switch
(SG300)
•
10/100BaseT 4 port VLAN-capable switch
(SG560, SG565, SG580)
•
Rear panel Ethernet link and activity status LEDs
DMZ link features (SG570, SG575 only)
•
10/100BaseT DMZ port
•
Real panel Ethernet link and activity status LEDs
Enviromental features
•
External power adaptor (voltage/current depends on individual model)
•
Front panel operating status LEDs: Power, Heart Beat
•
Operating temperature between 0° C and 40° C
•
Storage temperature between -20° C and 70° C
•
Humidity between 0 to 95% (non-condensing)
Page 14 / 249
Introduction
9
Your CyberGuard SG Rack Mount Appliance
CyberGuard SG rack mount appliances include:
•
SG710
•
SG710+
The following items are included with your CyberGuard SG rack mount appliance:
•
Power cable
•
Installation CD
•
Printed Quick Install guide
•
Cabling including
o
1 normal
straight through
UTP cable (blue color).
o
1
crossover
UTP cable (either gray or red color)
Front panel LEDs
The front panel contains LEDs indicating status.
An example of the front panel LEDs are
illustrated in the following figure and detailed in the following table.
Figure 1-3
Label
Activity
Description
Power
On
Power is supplied to the CyberGuard SG appliance
Flashing
The CyberGuard SG appliance is operating correctly
H/B
(Heart Beat)
On
If this LED is on and not flashing, an operating error
has occurred
Error! Reference source not found.
Failover
On
The CyberGuard SG appliance has switched to the
backup Internet connection
High Avail
On
Reserved to indicate failover to a backup device
(available in a future firmware release)
Online
On
An Internet connection has been established
Page 15 / 249
Introduction
10
Note
If
H/B
does not begin flashing 20 – 30 seconds after power is supplied, refer to Appendix
E,
Recovering From a Failed Upgrade.
Front panel
The front panel contains two 10/100 Ethernet four port switches (
A
and
B
), two 10/100
Ethernet ports (
C
and
D
) and analog/ISDN modem (
Serial
) as well as operating status
LEDs and the configuration reset button (
Erase
).
On the front panel Ethernet ports, the right hand LED indicates the
link
condition, where a
cable is connected correctly to another device.
The left hand LED indicates
network
activity
.
Rear panel
The rear panel contains a power switch and a power inlet for an IEC power cable.
Additionally, the SG710+ has two gigabit Ethernet ports (
E
and
F
).

Rate

4 / 5 based on 3 votes.

Popular SnapGear Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top