1. Home
    2. /
  2. Manuals
    3. /
  3. SMC
    4. /
  4. SMC7904WBRA-N
    5. /
  5. 5
Page 21 / 131 Scroll up to view Page 16 - 20
H
ARDWARE
D
ESCRIPTION
2-3
LED Indicators
The power and port LED indicators and the WPS button on the top panel
are illustrated in the following figure and table.
Figure 2-1.
Top View
Item
Status
Description
Power
On
The Barricade is receiving power. Normal
operation.
Off
Power off or failure.
ADSL
Sync
On
ADSL connection is functioning correctly.
Flashing
The Barricade is establishing an ADSL link.
Off
ADSL connection is not established.
ADSL
Data
Blinking
ADSL port is sending/receiving data.
Off
No data is being transferred.
WLAN
On
Wireless link established.
Blinking
Data is been transmitted via wireless link.
Page 22 / 131
I
NSTALLATION
2-4
Note:
with successful WPS connection, the WPS LED indicator will be
off after 300 seconds.
WLAN
Off
No wireless link.
WPS
On
Successful WPS connection.
Fast Flash
WPS connection failed.
Slow Flash
The Barricade is establishing WPS connection.
Off
WPS function is off.
LAN
(4 LEDs)
On
Ethernet connection is established.
Flashing
The indicated LAN port is sending or receiving
data.
Off
There is no LAN connection on the port.
WPS
button
This button is located on the top panel, press this
button for at least 4 seconds when activating the
WPS function.
Item
Status
Description
Page 23 / 131
H
ARDWARE
D
ESCRIPTION
2-5
Rear Panel
SMC7904BRA-N contains the following ports on the rear panel:
Figure 2-2.
Rear Panel
Item
Description
ADSL
Port
Connect your ADSL line to this port (RJ-11 port).
LAN1 to
LAN4
Fast Ethernet ports (RJ-45). Connect devices on your local
area network to these ports (i.e., a PC, hub, or switch).
Reset
Button
Use this button to reset the Barricade and restore the
default factory settings. To reset without losing
configuration settings, see “Reset” on page 4-78.
Power
Inlet
Connect the included power adapter to this inlet.
Warning
: Using the wrong type of power adapter may
damage the Barricade.
Power On/Off
switch
Use this switch to turn on/off the power.
Page 24 / 131
I
NSTALLATION
2-6
ISP Settings
Please collect the following information from your ISP before setting up
the Barricade:
•
ISP account user name and password
•
Protocol, encapsulation and VPI/VCI circuit numbers
•
DNS server address
•
IP address, subnet mask and default gateway (for fixed IP users only)
Connect the System
The Barricade can be positioned at any convenient location in your office
or home. No special wiring or cooling requirements are needed. You
should, however, comply with the following guidelines:
•
Keep the Barricade away from any heating devices.
•
Do not place the Barricade in a dusty or wet environment.
You should also remember to turn off the power, remove the power cord
from the outlet, and keep your hands dry when you install the Barricade.
Connect the ADSL Line
Connect the supplied ADSL cable from the port labelled ADSL on the
Splitter/Microfilter to the ADSL port on your Barricade. When inserting
the plug, be sure the tab on the plug clicks into position to ensure that it is
properly seated.
Note:
The ADSL port of SMC7904WBRA-N is RJ-11.
Page 25 / 131
C
ONNECT
THE
S
YSTEM
2-7
Attach to Your Network Using Ethernet Cabling
The four LAN ports on the Barricade auto-negotiate the connection speed
to 10 Mbps or 100 Mbps, as well as the transmission mode to half duplex
or full duplex.
Use RJ-45 cables to connect any of the four LAN ports on the Barricade
to an Ethernet adapter on your PC. Otherwise, cascade any of the LAN
ports on the Barricade to an Ethernet hub or switch, and then connect
your PC or other network equipment to the hub or switch. When inserting
an RJ-45 connector, be sure the tab on the connector clicks into position
to ensure that it is properly seated.
Warning:
Do not plug a phone jack connector into an RJ-45 port. This
may damage the Barricade.
Note:
Use 100-ohm shielded or unshielded twisted-pair cable with RJ-45
connectors for all Ethernet ports. Category 5 cable is
recommended. Make sure each twisted-pair cable length does not
exceed 100 meters (328 feet).
Connect the Power Adapter
Plug the power adapter into the power socket on the rear of the Barricade,
and the other end into a power outlet.
Check the power indicator on the front panel is lit. If the power i
ndicator is
not lit, refer to
“Troubleshooting” on page A-1.
In case of a power input failure, the Barricade will automatically restart and
begin to operate once the input power is restored.

Rate

3.5 / 5 based on 2 votes.

Popular SMC Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top