1. Home
    2. /
  2. Manuals
    3. /
  3. RadioLabs
    4. /
  4. O2Storm
    5. /
  5. 5
Page 21 / 77 Scroll up to view Page 16 - 20
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
13
II
Time Zone Setting
This page is used to enable and configure NTP client
Screen snapshot – Time Zone Settings
III
LAN Interface Setup
This page is used to configure local area network IP address and subnet
mask
Screen snapshot – LAN Interface Setup
Page 22 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
14
IV
WAN Interface Setup
This page is used to configure WAN access type
Screen snapshot – WAN Interface Setup
V
Wireless Basic Settings
This page is used to configure basic wireless parameters like Band, Mode,
Network Type SSID, Channel Number, Enable Mac Clone(Single
Ethernet Client)
Screen snapshot – Wireless Basic Settings
Page 23 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
15
VI
Wireless Security Setup
This page is used to configure wireless security
Screen snapshot – Wireless Security Setup
3.3.3
Operation Mode
This page is used to configure which mode wireless broadband router acts
Screen snapshot – Operation Mode
Item
Description
Gateway
Traditional gateway configuration. It always connects
internet via ADSL/Cable Modem. LAN interface, WAN
Page 24 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
16
interface, Wireless interface, NAT and Firewall modules
are applied to this mode
Bridge
Each interface (LAN, WAN and Wireless) regards as
bridge. NAT, Firewall and all router’s functions are not
supported
Wireless ISP
Switch Wireless interface to WAN port and all Ethernet
ports in bridge mode. Wireless interface can do all
router’s functions
Apply Changes
Click the
Apply Changes
button to complete the new
configuration setting.
Reset
Click the
Reset
button to abort change and recover the
previous configuration setting.
3.3.4
Wireless - Basic Settings
This page is used to configure the parameters for wireless LAN clients that may
connect to your Broadband Router. Here you may change wireless encryption
settings as well as wireless network parameters.
Screen snapshot – Wireless Basic Settings
Page 25 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
17
Item
Description
Disable Wireless LAN
Interface
Click on to disable the wireless LAN data transmission.
Band
Click to select 2.4GHz(B) / 2.4GHz(G) / 2.4GHz(B+G)
Mode
Click to select the WLAN AP / Client / WDS / AP+WDS
wireless mode.
Site Survey
The
Site Survey
button provides tool to scan the wireless
network. If any Access Point or IBSS is found, you could
choose to connect it manually when client mode is
enabled. Refer to 3.3.9 Site Survey.
SSID
It is the wireless network name. The SSID can be 32
bytes long.
Channel Number
Select the wireless communication channel from
pull-down menu.
Associated Clients
Click the
Show Active Clients
button to open Active
Wireless Client Table that shows the MAC address,
transmit-packet, receive-packet and transmission-rate for
each associated wireless client.
Enable Mac Clone
(Single Ethernet Client)
Take Laptop NIC MAC address as wireless client MAC
address.
[Client Mode only]
Enable Universal
Repeater Mode
Click to enable Universal Repeater Mode
SSID of Extended
Interface
Assign SSID when enables Universal Repeater Mode.
Apply Changes
Click the
Apply Changes
button to complete the new
configuration setting.
Reset
Click the
Reset
button to abort change and recover the
previous configuration setting.
3.3.5
Wireless - Advanced Settings
These settings are only for more technically advanced users who have a
sufficient knowledge about wireless LAN. These settings should not be changed
unless you know what effect the changes will have on your WLAN Broadband
Router.

Rate

3.5 / 5 based on 2 votes.

Popular RadioLabs Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top