Page 31 / 59 Scroll up to view Page 26 - 30
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 31 of 59
8.6
DMZ
A DMZ (Demilitarized Zone) allows a single computer on your LAN to expose ALL of its
ports to the Internet. Enter the IP address of that computer as a DMZ (Demilitarized Zone)
host with unrestricted Internet access. When doing this, the DMZ host is no longer behind
the firewall.
Fields in this page:
Field
Description
Enable DMZ
Check this item to enable the DMZ feature.
DMZ Host IP
Address
IP address of the local host. This feature sets a local host to be exposed to the
Internet.
Function buttons in this page:
Apply Changes
Click to save the setting to the configuration.
Page 32 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 32 of 59
8.7
IGMP PROXY CONFIGURATION
Multicasting is useful when the same data needs to be sent to more than one hosts. Using
multicasting, as opposed to sending the same data to the individual hosts uses less
network bandwidth. The multicast feature also enables you to receive multicast video
stream from multicast servers.
IP hosts use Internet Group Management Protocol (IGMP) to report their multicast group
memberships to neighboring routers. Similarly, multicast routers use IGMP to discover
which of their hosts belong to multicast groups. Hurricane 5200C/5201 supports IGMP
proxy that handles IGMP messages. When enabled, this modem/router acts as a proxy for
a LAN host making requests to join and leave multicast groups, or a multicast router
sending multicast packets to multicast group on the WAN side.
When a host wishes to join a multicast group, it sends IGMP REPORT message to
Hurricane 5200C’s IGMP downstream interface. The proxy sets up a multicast route for the
interface and host requesting the video content. It then forwards the Join to the upstream
multicast router. The multicast IP traffic will then be forwarded to the requesting host. On a
leave, the proxy removes the route and then forwards the leave to the upstream multicast
router.
The IGMP Proxy page allows you to enable multicast on WAN and LAN interfaces. The
LAN interface is always served as a downstream IGMP proxy, and you can configure one
of the available WAN interfaces as the upstream IGMP proxy.
±
Upstream
: The interface that IGMP requests from hosts (LAN) is sent to the
multicast router.
±
Downstream
: The interface data from the multicast router are sent to hosts (LAN)
in the multicast group database.
Page 33 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 33 of 59
Fields in this page:
Field
Description
IGMP Proxy
Enable/disable IGMP proxy feature
Proxy Interface
The upstream WAN interface is selected here.
Function buttons in this page:
Apply Changes
Click to save the setting to the configuration.
Undo
Discard your settings.
Page 34 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 34 of 59
8.8
UPnP CONFIGURATION
The modem/router supports a control point for Universal Plug and Play (UPnP) version 1.0,
and supports two key features:
NAT Traversal
and
Device Identification
. This feature
requires one active WAN interface. In addition, the host should support this feature. In the
presence of multiple WAN interfaces, select an interface on which the incoming traffic is
present.
With NAT Traversal, when UPnP command is received to open ports in NAT, the
application translates the request into system commands to open the ports in NAT and the
firewall.
For Device Identification, the application will send a description of the modem/router as a
control point back to the host making the request.
Page 35 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 35 of 59
Fields in this page
Field
Description
UPnP
Enable/disable UPnP feature.
WAN Interface
Select WAN interface that will use UPnP from the drop-down list box.
Function buttons in this page:
Apply Changes
Click to save the setting to the system configuration.
8.9
RIP CONFIGURATION
RIP (Routing Information Protocol) is an Internet protocol that you can set up to share
routing table information with other routing devices on your LAN, at your ISP’s location, or
on remote networks connected to your LAN via ADSL line.
Most home or small office networks do not need to use RIP; they have only one router,
such as the ADSL Router, and one path to an ISP. In this case, there is no need to share
routes, because all Internet data from the network is sent to the same ISP gateway.
You may want to configure RIP if any of the following circumstances apply to your network:
Your home network setup includes an additional router or RIP-enabled PC (other
than the ADSL Router). The ADSL Router and the router will need to communicate
via RIP to share their routing tables.
Your network connects via the ADSL line to a remote network, such as a corporate
network. In order for your LAN to learn the routes used within your corporate
network, they should both be configured with RIP.
Your ISP requests that you run RIP for communication with devices on their
network.

Rate

4.3 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top