802.11n Wireless ADSL2/2+ Router

ADN-4101

3.3.2 LAN

Choose

Status

>

LAN

and the page displayed shows some basic LAN settings of the router. On this page, you can

view the LAN IP address, DHCP server status, MAC address, and DHCP client table.

3.3.3 WLAN

Choose

Status

>

WLAN

and the page displayed shows some basic settings of wireless LAN (WLAN).

21

802.11n Wireless ADSL2/2+ Router

ADN-4101

3.3.4 WAN

22

AN.

Choose

Status

>

WAN

and the page displayed shows some basic WAN settings of the router. On this page, you can

view basic status of WAN and DNS server. If you want to configure the WAN network, refer to chapter 0.1373892

3.3.4 3.4.2.1 W

3.3.5 Port Mapping

Choose

Status

>

Port Mapping

. On this page, you can view the mapping relation and the status of port mapping.

802.11n Wireless ADSL2/2+ Router

ADN-4101

3.3.6 Statistics

Choose

Status

>

Statistics.

The

Statistics

page that is displayed contains

Statistics

and

ADSL Statistics

.

3.3.6.1 Statistics

Click

Statistics

in the left pane and the page shown in the following figure appears. On this page, you can view the

statistics of each network port.

3.3.6.2 ADSL Statistics

Click

ADSL Statistics

in the left pane and the page shown in the following figure appears. On this page, you can view

the ADSL line status, upstream rate, downstream rate and other information.

23

802.11n Wireless ADSL2/2+ Router

ADN-4101

3.3.7 ARP Table

Choose

Status

>

ARP

.

On the

ARP Table

page, you can view the table that shows a list of learned MAC addresses.

3.4 Network

In the navigation bar, click

Network

.

The

Network

page that is displayed contains

LAN, WAN

, and

WLAN.

3.4.1 LAN

Choose

Network

>

LAN

. The

LAN

page that is displayed contains

LAN IP

,

DHCP

and

DHCP Static IP

.

3.4.1.1 LAN IP

Click

LAN IP

in the left pane and the page shown in the following figure appears.On this page, you can change IP

address of the router. The default IP address is

192.168.1.1

, which is the private IP address of the router.

24

802.11n Wireless ADSL2/2+ Router

ADN-4101

The following table describes the parameters on this page:

Field

Description

IP Address

Enter the IP address of LAN interface. It is recommended to use an address from

a block that is reserved for private use. This address block is

192.168.1.1

-

192.168.1.254

.

Subnet Mask

Enter the subnet mask of LAN interface. The range of subnet mask is from

255.255.0.0

-

255.255.255.254

.

Secondary IP

Select it to enable the secondary LAN IP address. The two LAN IP addresses

must be in the different network.

LAN Port

You can choose the LAN interface you want to configure.

Link Speed/Duplex Mode

You can select the following modes from the drop-downlist:

100Mbps/FullDuplex

,

100Mbps/Half Duplex

,

10Mbps/FullDuplex

,

10Mbps/Half Duplex

,

Auto Negotiation

.

MAC Address Control

It is the access control based on MAC address. When selecting it, the host

whose MAC address is listed in the

Current Allowed MAC Address Table

can

access the modem.

Add

Enter MAC address, and then click it to add a new MAC address.

3.4.1.2 DHCP

Dynamic Host Configuration Protocol (DHCP) allows the individual PC to obtain the TCP/IP configuration from the

centralized DHCP server. You can configure this router as a DHCP server or disable it. The DHCP server can assign

IP address, IP default gateway, and DNS server to DHCP clients. This router can also act as a surrogate DHCP server

(DHCP Relay) where it relays IP address assignment from an actual real DHCP server to clients. You can enable or

disable DHCP server.

Click

DHCP

in the left pane and the page shown in the following figure appears.

The following table describes the parameters on this page:

Field

Description

DHCP Mode

If set to

DHCP Server

, the router can assign IP addresses, IP default gateway

and DNS Servers to the host in Windows95, Windows NT and other operation

systems that support the DHCP client.

IP Pool Range

It specifies the first and the last IP address in the IP address pool. The router

assigns IP address that is in the IP pool range to the host.

Show Client

Click it, the

Active DHCP Client Table

appears. It shows IP addresses

25