(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

35

OGU 930500105-A1

Quick Setup

Section

This chapter will describe the

Quick Setup Section

accessible from

the

Home Page

of the

DISCUS™ Multiplay Wireless VoIP AG

upon

user authentication to the Router.

The

Quick Setup

enables speedy and accurate configuration of your

Internet connection and other important parameters.

After the setup described in this chapter, you can immediately start

using your Router to:

1.

Share a broadband connection among multiple users (HTTP, FTP, Telnet,

NetMeeting) and between all of the computers connected to your home

network.

2.

Build a home network by connecting additional PCs and network

devices to the gateway.

3.

Share resources (file servers, printers, etc.) between computers in the

home network using their names; auto-learning DNS enables

DIS-

CUS™ Multiplay Wireless VoIP AG

to automatically detect the net-

work identification names of the LAN PCs, enabling mutual

communication using names, not IP addresses.

4.

Control network parameters, including DHCP, DNS and WAN settings.

5.

View network status, traffic statistics, system log and more.

Be aware that any configuration changes could compromise your connectivity.

DISCUS™ Multiplay Wireless VoIP AG

(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

36

OGU 930500105-A1

Quick Setup Section

6.

Allow access from the Internet to games and other services provided by computers

in the home network.

7.

Prohibit computers in the home network from accessing selected services on the

Internet.

8.

Block access to specific Internet Web sites from your home network.

FIGURE 1.

Quick Setup Panel

Your WAN connection(s) can be configured using one of the following meth-

ods. Read the configuration instructions relevant to you, by selecting your con-

nection method from the list below and clicking its section link:

1.

Point-to-point protocol over Ethernet (PPPoE)

2.

Point-to-point protocol over ATM (PPPoA)

3.

Routed Ethernet Connection over ATM (ETHoA)

4.

Bridged Ethernet Connection over ATM (ETHoA)

5.

No Internet connection

POINT-TO-POINT

PROTOCOL OVER

ETHERNET (PPPOE)

To configure the Point-to-point protocol over Ethernet, follow these steps:

1.

Select 'Point-to-point protocol over Ethernet (PPPoE)' from the 'Connection Type'

combo-box.

2.

Your Internet Service Provider (ISP) should provide you with the Login user name

and Login password.

3.

If your board features a DSL connection, you will see an 'Automatic PVC Scan'

check box. Select this check box to enable the automatic configuration of the VPI,

VCI and encapsulation parameters (relevant to DSL connections).

DISCUS™ Multiplay Wireless VoIP AG

(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

37

OGU 930500105-A1

Quick Setup Section

POINT-TO-POINT

PROTOCOL OVER ATM

(PPPOA)

To configure the Point-to-point protocol over ATM, follow these steps:

1.

Select 'Point-to-point protocol over ATM (PPPoA)' from the 'Connection Type'

combo-box

2.

Your Internet Service Provider (ISP) should provide you with the following informa-

tion:

- Login user name

- Login password

- By default, the 'Automatic PVC Scan' check box is enabled, which means that the

Router configures the VPI, VCI and encapsulation parameters automatically. If you

would like to configure these parameters manually, uncheck this check box.

- Specify the VPI and VCI values.

- Select the encapsulation method from the combo-box. You can choose among the

following methods: LLC, VCMux and VCMux - HDLC

ROUTED ETHERNET

CONNECTION OVER ATM

(ETHOA)

To configure the Routed Ethernet connection over ATM, follow these steps:

1.

Select 'Routed Ethernet Connection over ATM (ETHoA)' from the 'Connection

Type' combo-box

2.

Your Internet Service Provider (ISP) should provide you with the following informa-

tion:

- Specify the value of the VPI and VCI parameters.

- Select the encapsulation method from the combo-box. You can choose among the

following methods: LLC, VCMux.

- Select the Internet Protocol: Most Internet Service Providers (ISPs) provide

dynamic IP addresses, hence the default "Obtain an IP Address Automatically".

Should this not be the case, select the "Use the Following IP Address" option. The

screen will refresh. Enter the IP Address, Subnet Mask, Default Gateway, and DNS

Server details provided to you by your ISP.

BRIDGED ETHERNET

CONNECTION OVER ATM

(ETHOA)

To configure the Bridged Ethernet Connection over ATM (ETHoA), follow these

steps:

1.

Select 'Bridged Ethernet Connection over ATM (ETHoA)' from the 'Connection

Type' combo-box

2.

Your Internet Service Provider (ISP) should provide you with the following informa-

tion:

- Specify the value of the VPI and VCI parameters.

- Select the encapsulation method from the combo-box. You can choose among the

following methods: LLC, VCMux

NO INTERNET

CONNECTION

Select 'No Internet Connection' from the 'Connection Type' combo-box. Choose

this connection type if you do not have an Internet connection, or if you want to

disable all existing connections.

WIRELESS

Click the 'Enabled' check box to enable your wireless connection. Specify the

wireless network's ID in the 'SSID' field. The default SSID is 'openrg'.

DISCUS™ Multiplay Wireless VoIP AG

(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

38

OGU 930500105-A1

Quick Setup Section

ADMINISTRATOR

In this section it is necessary to specify the administrator's e-mail in the 'E-mail'

field. System alerts and notifications are sent to this address.

(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

39

OGU 930500105-A1

Network

Connections

Section

This chapter will describe the

Network Connections Section

acces-

sible from the

Home Page

of the

DISCUS™ Multiplay Wireless

VoIP AG

.

This section (see Figure 1) is intended to present a summary of the

Router's connections, such as WAN and LAN (i.e. Ethernet, USB,

Wireless) interfaces.

DISCUS™ Multiplay Wireless VoIP AG

supports various network

connections, both physical and logical. The Network Connections

screen enables you to configure the various parameters of your phys-

ical connections, the LAN and WAN, and create new connections,

using tunneling protocols over existing connections, such as PPP

and VPN.

Press the 'Advanced' button to expand the screen and display all

connection entries.

Be aware that any configuration changes could compromise your connectivity.