Page 16 / 116 Scroll up to view Page 11 - 15
I
NSTALLATION
2-6
Phone Line Configuration
Installing a Full-Rate Connection
If you are using a full-rate (G.dmt) connection, your service provider will
attach the outside ADSL line to a data/voice splitter. In this case you can
connect your phones and computer directly to the splitter as shown below:
Figure 2-3.
Installing with a Splitter
Voice
Data
Residential
Connection
Point [Network
Interface
Device (NID)]
Plain Old
Telephone
System (POTS)
or
Ethernet
hub or switch
ADSL Router
Splitter
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 116
C
ONNECT
THE
S
YSTEM
2-7
Installing a Splitterless Connection
If you are using a splitterless (G.lite) connection, then your service
provider will attach the outside ADSL line directly to your phone system.
In this case you can connect your phones and computer directly to the
incoming ADSL line, but you will have to add low-pass filters to your
phones as shown below:
Figure 2-4.
Installing without a Splitter
Plain Old
Telephone
System (POTS)
Filter
or
Ethernet
hub or switch
Voice
& Data
Voice
& Data
Data
Voice
ADSL Router
Residential
Connection
Point [Network
Interface
Device (NID)]
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 116
I
NSTALLATION
2-8
Attach to Your Network Using Ethernet Cabling
The four LAN ports on the ADSL Router auto-negotiate the connection
speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the
transmission mode to half duplex or full duplex.
Use RJ-45 cables to connect any of the four LAN ports on the ADSL
Router to an Ethernet adapter on your PC. Otherwise, cascade any of the
LAN ports on the ADSL Router to an Ethernet hub or switch, and then
connect your PC or other network equipment to the hub or switch. When
inserting an RJ-45 connector, be sure the tab on the connector clicks into
position to ensure that it is properly seated.
Warning:
Do not plug a phone jack connector into an RJ-45 port. This
may damage the ADSL Router.
Notes: 1.
Use 100-ohm shielded or unshielded twisted-pair cable with
RJ-45 connectors for all Ethernet ports. Use Category 3, 4, or 5
for connections that operate at 10 Mbps, and Category 5 for
connections that operate at 100 Mbps.
2.
Make sure each twisted-pair cable length does not exceed
100 meters (328 feet).
Connect the Power Adapter
Plug the power adapter into the power socket on the rear of the ADSL
Router, and the other end into a power outlet.
Check the power indicator on the front panel is lit. If the power i
ndicator is
not lit, refer to
“Troubleshooting” on page A-1.
In case of a power input failure, the ADSL Router will automatically restart
and begin to operate once the input power is restored.
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 116
3-1
C
HAPTER
3
C
ONFIGURING
C
LIENT
PC
After completing hardware setup by connecting all your network devices,
you need to configure your computer to connect to the ADSL Router.
See:
“Windows 98/Me” on page 3-3
“Windows NT 4.0” on page 3-8
“Windows 2000” on page 3-12
“Windows XP” on page 3-15
or
“Configuring Your Macintosh Computer” on page 3-17
depending on your operating system.
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 116
C
ONFIGURING
C
LIENT
PC
3-2
TCP/IP Configuration
To access the Internet through the ADSL Router, you must configure the
network settings of the computers on your LAN to use the same IP subnet
as the ADSL Router. The default IP settings for the ADSL Router are:
Note:
These settings can be changed to fit your network requirements,
but you must first configure at least one computer to access the
ADSL Router’s web configuration interface in order to make the
required changes. (See “Configuring the ADSL Router” on page
4-1 for instruction on configuring the ADSL Router.)
IP Address
192.168.2.1
Subnet Mask
255.255.255.0
DHCP function
Enable
DHCP IP Pool Range
192.168.2.2 to
192.168.2.254
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Ozenda Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top