300Mbps Wireless-N AP / Repeater / Router clientUser Manual

30



WPS Status: Display WPS (Wi-Fi Protected Setup) status is enabled or not.

4.1.5.

Router Status

This item provides current running information of System.

Figure 4-5

4.1.6.

Traffic Statistics

This item provides statistics information about the bits router sends and received.

Figure 4-6

4.2.

Quick Setup

Providing you the convenient and simplest method for configure the router, the purpose of this

item is to provide an easy way for you to use it and configure your router to access the Internet

quickly; including ‘DHCP

（

dynamic

）

’, ‘PPPoE’, ‘Static’and ‘Wireless Configuration’. This is

the most convenient tool for you to configure router.

4.2.1.

DHCP (dynamic)

After select this item, you will obtain an IP address from your ISP automatically, those ISP who

supply Cable modem always use DHCP technology.

Figure 4-7

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

31

4.2.2.

PPPoE

Figure 4-8

If your ISP provides you the PPPoE service (all ISP with DSL transaction will supply this

service, such as the most popular ADSL technique), please select this item. In the “Convenient

configuration” You can input your PPPoE username and password to access the Internet.



PPPoEUsername: Input PPPoE username provided by ISP



PPPoE Password: Input PPPoE password provided by ISP.

4.2.3.

Static

Figure 4-9

This item should only be used when users use a static IP address to access Internet, you should

input your “WAN IP address”, ”subnet mask”,” default gateway” and “DNS server (domain

name server)” according to the information provided by your ISP. And every IP address should

be input in appropriate IP field, a IP address only divided into four IP octets by sign“.” is

acceptable.



WAN IP address: The IP address that your Internet access into



Subnet mask: Specify a Subnet Mask for your WAN segment



Default gateway: It is provided by your ISP



Primary DNS: DNS server is used for resolve domain name. Your ISP will provides you

with at least one DNS IP address, input IP address of your DNS server in this field



Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank.

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

32

4.2.4.

Wireless Configuration

You can choose “Enable” or “Disable” to enable or disable the wireless function. The default

setting is “enable”. If you chose the “Disable” status, the router will become a wired broadband

router without wireless function, so be careful when you choose this status.

Figure 4-10



SSID: SSID (Service Set Identifier) is your wireless network's name shared among all

points in a wireless network. The SSID must be identical for all devices in the wireless

network. It is case-sensitive and must not exceed 32 characters. Make sure all points in the

wireless network have the same SSID. For added security, you should change the default

SSID to a unique name.



Region:Choose a correct region which fit your use environment.



Channel: Wireless router communicates to wireless cards in a particular channel, which

can reduce interference between different channels.



Authentication Type: Different authentication types use different encryption types, which

can encrypt wireless data to protect your wireless communication.

4.2.5.

MAC Clone

The WAN port of router has a unique MAC address assigned by manufacturer; it called as

“Default MAC”. The “Clone MAC” is used for some special situations; For example, ISP only

allows certain MAC address to access the Internet, thus you can modify your WAN port’s MAC

address in accord with the requirement of ISP, avoiding ISP’s detection.

Figure 4-11

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

33

4.3.

WPS Settings

Wi-Fi Protect Setup (WPS) function can let you create a safety network easily. You can through

‘PIN Input Config (PIN)’ or ’Push Button (PBC)’to encrypt your network. This router also

provides WPS button, you only need to push the WPS button in this router and the wireless

network card that support WPS function, then the router will be encrypted to WPA2-AES mode

automatically

Note:

If you have configured encryption mode in your router, then when you use this WPS function,

please configure the authentication type to none, and then it will be encrypted to WPA2-AES

mode automatically. If you don’t want to change your authentication type, then when you use

this function, the router will be encrypted to the mode that you have configured.

4.3.1.

WPS Settings

Figure 4-12



WPS Status: You can use this function to setup the wireless connection between this router

and wireless network card. The default is Enable.



AP PIN Code: This code can mark a wireless product.



Add A New Device: Add a new device by WPS.

4.3.2.

Add a New Device

Figure 4-13



Enter the new device’s PIN: This code can mark a wireless product.



Press the button of the new device in two minutes: New device will send a PIN code to

wireless router.

WPS can connect the wireless adapter and the router in a safe way. If you have a wireless

network card which has WPS button, you may set up a safe network via the following methods.

Method 1:

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

34

1. Push the WPS button in the Router until the WPS LED is flashing several times.

2. Push the WPS button in the wireless network cardfor about 3-5seconds.

3. The safe connection will be established automatically.

Method 2:

1. Input the PIN code of the adapter’s WPS page into the router’s WPS configure page, then

click ’connect’.

Figure 4-14

Figure 4-15

2. Push the ‘PIN Input Config (PIN)’ in the Wi-Fi protect setup of the adapter

Figure 4-16

3. Select this router in the pop-up window, then click ‘Select’

4. The connection between the adapter and the router is be established automatically.

Method 3:

1. Select ‘Input PIN from AP’ in WI-FI protect setup page, input PIN of the router, then click

‘PIN Input Config (PIN)’

2. Select this router in the pop-up window, then click ‘Select’

3. The connection between the adapter and the router is be established automatically.

Remark

If there is more than one AP in the PBC mode when you use the method 1, there will be session

overlap. Please using method 2/3 or wait for a while push the button again.

4.3.3.

WPS Configuration

Display the WPS configuration information.