300Mbps Wireless-N AP / Repeater / Router clientUser Manual

5

4.12.6.

Remote Management

...............................................................................................

57

4.12.7.

Factory Defaults

......................................................................................................

57

4.12.8.

Reboot

.....................................................................................................................

57

4.13.

A

BOUT

.............................................................................................................................

58

5.

TROUBLESHOOTING

.........................................................................................................

58

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

6

1.

Introduction

1.1.

Product Overview

300Mbps Wireless-N AP/ Repeater/ Router clientis dedicated to Small Office/Home Office

(SOHO) Wireless network solution. It is 4 in 1 network device, which combines wireless

access point, firewall, 4-port Switch and the NAT-Router. It provides up to 300Mbps data

transmission rate in 2.4GHz frequency, complies with IEEE 802.11n, IEEE 802.11g and

IEEE802.11b and backwards compatible with all IEEE 802.11n/g/b devices.And the router

also supports wireless LAN up to 128-bit WEP, WPA/WPA2encryption security. The

300Mbps Wireless-N AP/ Repeater/ Router clientalso provides WEB and Remote

Management and system log so that network administrators can manage and monitor the

network in real time.

The 300Mbps Wireless-N AP/ Repeater/ Router clientalso provides a hardware WPS (Wi-Fi

protected setup) button, which helps you setup a secure wireless network in a snap. The

button lets you activate the wireless protection easily.

1.2.

Main Features



Comply with IEEE802.11n/g/b, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX

standards



Support MIMO technology with 2 transmit and 2 receive, up to 300Mbps wireless LAN

data transfer rates



Support DHCP Client, PPPoE Client, Static IP, L2TP, PPTP



Support multi-wireless mode: AP, WDS, AP+WDS, repeater, client, etc.



Support static ARP, MAC filtering, IP access control, DNS filter



Support FTP, PPTP and L2TP pass through



Support UPNP (universal plug and play)



Upgradeable firmware for future functions



WPS button can easily setup a secure network



Support WMM



Support data encryption mode: WEP, WPA, WPA2



Support DMZ

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

7

1.3.

Supporting Standard and Protocol



IEEE 802.11b/g/n



IEEE 802.11e



IEEE 802.11h



IEEE 802.11k



IEEE 802.11i



IEEE 802.3 10Base-T



IEEE 802.3u 100Base-TX

1.4.

Working Environment

Temperature



0° to 40° C (operating)



-40° to 70° C (storage)

Humidity



10% to 90 % non-condensing (operating)



5% to 90% non-condensing (storage)

Power



DC 9V

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

8

2.

Hardware Installation

2.1.

System Requirement

Minimum Requirements:



Broadband (DSL/Cable) modem and service with Ethernet port



802.11n b/g/n wireless adapter or Ethernet adapter and cable for each computer



Internet Explorer® 5.0, Firefox® 2.0 or Safari® 1.4 or higher

2.2.

Panel

Front panel

Figure 2-1

LED

Function

PWR

ON

Power on

Off

Power off

WPS

Flashing

slowly

WPS is running

OFF

WPS is not running

SYS

ON and Off

Abnormal

Flashing

Normal

WAN

On

WAN Connection normal

Flashing

Data transmitting

Off

WAN Connection abnormal

300Mbps Wireless-N AP / Repeater / Router clientUser Manual

9

LAN

On

LAN Connection normal

Flashing

Data transmitting

Off

LAN Connection abnormal

Rear panel

Figure 2-2

Description

Function

PWR

Connect to Power adapter, please don’t use the unknown

power adapter, otherwise your device may be damaged.

SYS

Direction system run abnormal or normal

Default

Restore settings

WPS

“WPS” Encryption button

WAN

Internet access

LAN

Connect with computer NIC or Ethernet device

2.3.

Restore to factory configuration

If the router ever freezes in a setting change process or if you can’t access it because you can’t

remember the IP you have given it or other problem, you may have to utilize the reset button on

the back of the router to put it back to factory settings. You have to press and hole this button

for a few seconds (2-6s) with a pencil when it is working, then release and it will restore

settings to the factory configuration.

The other way to restore factory settings is through the same user interface used in setup.

Click on ‘System management’- ‘Restore’, and click on the ‘Restore’ button.

2.4.

Hardware Installation Procedures

The procedures to install the 150Mbps Wireless-N AP/ Repeater / Router client pleaserefers to

the following picture