150Mbps Wireless-N AP/ Repeater / Router clientUser Manual

5

4.12.6.

Remote Management

...............................................................................................

57

4.12.7.

Factory Defaults

......................................................................................................

57

4.12.8.

Reboot

.....................................................................................................................

57

4.13.

A

BOUT

.............................................................................................................................

58

5.

TROUBLESHOOTING

.........................................................................................................

58

150Mbps Wireless-N AP/ Repeater / Router clientUser Manual

6

1.

Introduction

1.1.

Product Overview

The 150Mbps Wireless-N AP/ Repeater / Router client

is dedicated to Small Office/Home

Office (SOHO) Wireless network solution. It is 4 in 1 network device, which combines

wireless access point, firewall, 4-port Switch and the NAT-Router. It provides up to 150Mbps

data transmission rate in 2.4GHz frequency, complies with IEEE 802.11n, IEEE 802.11g and

IEEE802.11b and backwards compatible with all IEEE 802.11n/g/b devices.And the router

also supports wireless LAN up to 128-bit WEP, WPA/WPA2encryption security. The

150Mbps Wireless-N AP/ Repeater / Router client

also provides WEB and Remote

Management and system log so that network administrators can manage and monitor the

network in real time.

The 150Mbps Wireless-N AP/ Repeater / Router client alsoprovides a hardware WPS (Wi-Fi

protected setup) button, which helps you setup a secure wireless network in a snap. The

button lets you activate the wireless protection easily.

1.2.

Main Features

➘

Comply with IEEE802.11n/g/b, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX

standards

➘

Support DHCP Client, PPPoE Client, Static IP, L2TP, PPTP

➘

Support multi-wireless mode: AP, WDS, AP+WDS, repeater, client, etc.

➘

Support static ARP, MAC filtering, IP access control, DNS filter

➘

Support FTP, PPTP and L2TP pass through

➘

Support UPNP (universal plug and play)

➘

Upgradeable firmware for future functions

➘

WPS button can easily setup a secure network

➘

Support WMM

➘

Support data encryption mode: WEP, WPA, WPA2

➘

Support DMZ

1.3.

Supporting Standard and Protocol

➘

IEEE 802.11b/g/n

150Mbps Wireless-N AP/ Repeater / Router clientUser Manual

7

➘

IEEE 802.11e

➘

IEEE 802.11h

➘

IEEE 802.11k

➘

IEEE 802.11i

➘

IEEE 802.3 10Base-T

➘

IEEE 802.3u 100Base-TX

1.4.

Working Environment

Temperature

➘

0° to 40° C (operating)

➘

-40° to 70° C (storage)

Humidity

➘

10% to 90 % non-condensing (operating)

➘

5% to 90% non-condensing (storage)

Power

➘

DC 9V

150Mbps Wireless-N AP/ Repeater / Router clientUser Manual

8

2.

Hardware Installation

2.1.

System Requirement

Minimum Requirements:

➘

Broadband (DSL/Cable) modem and service with Ethernet port

➘

802.11n b/g/n wireless adapter or Ethernet adapter and cable for each computer

➘

Internet Explorer® 5.0, Firefox® 2.0 or Safari® 1.4 or higher

2.2.

Panel

Front panel

Figure 2-1

Rear panel

150Mbps Wireless-N AP/ Repeater / Router clientUser Manual

9

Figure 2-2

Description

Function

PWR

Connect to Power adapter, please don’t use the unknown

power adapter, otherwise your device may be damaged.

Default

Restore settings

WPS

“WPS” Encryption button

WAN

Internet access

LAN

Connect with computer NIC or Ethernet device

2.3.

Restore to factory configuration

If the router ever freezes in a setting change process or if you can’t access it because you can’t

remember the IP you have given it or other problem, you may have to utilize the reset button on

the back of the router to put it back to factory settings. You have to press and hole this button

for a few seconds (2-6s) with a pencil when it is working, then release and it will restore

settings to the factory configuration.

The other way to restore factory settings is through the same user interface used in setup.

Click on ‘System management’- ‘Restore’, and click on the ‘Restore’ button.

2.4.

Hardware Installation Procedures

The procedures to install the 150Mbps Wireless-N AP/ Repeater / Router client pleaserefers to

the following picture