M S I R G 3 0 0 E X （ L i t e )

The wizard will now save the settings and will close the screen automatically.

3.5 Finishing the installation procedure of your wireless

router

After following chapter 3, you can finish the installation procedure by following the next

steps:

1. Remove the UTP network cable from your computer.

2. Remove the UTP networking cable from the LAN port of your RG300EX

（

Lite).

3. Restart your computer.

4. Congratulations! You have properly installed the RG300EX

（

Lite).

An explanation how to connect your wireless network using Windows XP and Windows Vista can be found

in chapter 6.0

3.6 Configuration as an Access Point

Install the RG300EX

（

Lite) as an access point if you have a router or DSL modem router. Make sure that

your Internet browser and your network are well configured when configuring manually. You can assume

that the settings are correct, unless you have changed any of the settings in the past.

Example of RG300EX

（

Lite) as an Access Point

Page 25 of 52

M S I R G 3 0 0 E X （ L i t e )

3.7 Connecting the RG300EX

（

Lite)

1. Turn off the computer.

2. Connect the RG300EX

（

Lite) to a wall outlet using the supplied power adapter.

3. Connect the supplied UTP network cable to the ‘LAN 4’ port of the RG300EX

（

Lite).

4. Connect the other end of this UTP network cable to the network adapter of your computer.

Is my RG300EX

（

Lite) correctly connected to the wall outlet? You can check this by verifying that the

POWER LED is on or not.

Do I have a proper network connection? Turn on the computer and verify if the LED on the RG300EX

（

Lite), corresponding with the LAN-port to which you connected the UTP networking cable, is lit. The

LED on the network adapter of your computer should also be lit.

3.8 Configuring the RG300EX

（

Lite) as an Access Point

Before you can configure the RG300EX

（

Lite) for an Internet connection you first need to connect to the

RG300EX

（

Lite) by following the procedure below.

1. Turn on your computer.

2. Open your web browser (e.g. Internet Explorer, Netscape of Firefox).

3. Type ‘http://192.168.0.1’ in the address bar.

4. Press the ‘Enter key’ or click ‘Go to’. You will now be asked for a ‘Username’ and a ‘Password’. Fill in

‘admin’ in the ‘Username’ field and ‘admin’ in the ‘Password’ field and press the enter key.

5. Click ‘Setup Tool’.

Page 26 of 52

M S I R G 3 0 0 E X （ L i t e )

6. Click ‘Advanced Setup’ in the left menu.

7. Click ‘Network’ in the left menu.

8. Click ‘LAN/DHCP Server’.

9. Select ‘Stop’ at ‘DHCP Server’.

Page 27 of 52

M S I R G 3 0 0 E X （ L i t e )

10. Click ‘Apply’ at the right side in the menu ‘DHCP Server’.

11. Type ‘192.168.0.200’ in the ‘LAN IP address’ field.

12. Type ‘255.255.255.0’ in the ‘Subnet mask’ field.

13. Click the button ‘Apply & Restart’.

Note! If you wish to log in to your RG300EX

（

Lite) at a later point in time, you must assign a fixed IP-

address to your computer.

1. Click ‘Start’.

2. Double click ‘Network Connections’.

Page 28 of 52

M S I R G 3 0 0 E X （ L i t e )

3. Right click the appropriate ’LAN Connection’

.

4. Click ‘Properties’.

Page 29 of 52