Installing the Gateway

B

SVG6x82 Series Wireless Voice Gateway

•

User Guide

8

590934-001-a

3.

Connect the Ethernet cable to any open Ethernet port on the gateway.

4.

Connect the other end of the Ethernet cable to the Ethernet port on your computer.

Repeat steps 3 and 4 for each additional computer or other device.

5.

Plug the telephone cord of a single- or two-line telephone into your telephone.

6.

Plug the other end of the telephone cord into the TEL 1 port on the gateway.

7.

Use the TEL 1 port to connect two-line telephones.

Note

: Contact a VoIP service provider to activate this service.

8.

For a second telephone, plug the telephone cord of a single-line telephone into the TEL 2 port on the

gateway.

9.

Plug the power cord into the Power port on the gateway.

10.

Plug the other end of the power cord into an electrical wall outlet. This automatically powers ON the

gateway.

Testing the Gateway Connections

Perform the following gateway connectivity test to verify that all the components were connected

properly:

1.

Power ON your computer and then log on.

2.

Check that all the LEDs on the front panel of the gateway first FLASH in sequential order and then

light SOLID. See

Front Panel

for additional LED status information.

If an LED did not light SOLID, contact your service provider for assistance.

3.

Contact your service provider to activate (provision) the gateway.

Note

: Your service provider may allow for automatic activation which will automatically launch a

special website when you open a web browser.

4.

Once your gateway is provisioned, open a web browser on your computer, such as Internet Explorer,

Firefox, Google Chrome, or Safari.

5.

Type a valid URL (for example,

www.motorola.com

) in the address bar and then click or press

Enter

.

If the web page did not open, contact your service provider for assistance or proceed to

Connecting

the Gateway to the Internet

to manually set up the network options on your computer.

Setting Up an Internet Connection

IMPORTANT!

Your computer may already be configured to automatically connect to the

Internet. If so,

do not

change the network options before contacting your service provider

for assistance.

If you cannot access the Internet after completing the gateway installation, you may have to manually set

up your computer to connect to the Internet. To do this, you will have to enable the network options on

your computer to automatically obtain an IP address and DNS server address.

Please note, operating system-specific commands for configuring computer network options are not

provided in this document.

Installing the Gateway

B

SVG6x82 Series Wireless Voice Gateway

•

User Guide

9

590934-001-a

The general steps provided below can be used for the following Microsoft Windows platforms:

•

Windows 7

•

Windows Vista

•

Windows XP

For specific commands, refer to the documentation for the Windows operating system running on your

computer for specific commands.

1.

Click the

Start

button from the Taskbar on your desktop and then click

Control Panel

and

Network

Connections

.

Note

: Additional selections may be necessary for Windows 7 systems.

2.

Step through to open the Local Area Connection Properties window.

3.

Select

Internet Protocol (TCP/IP)

option and click

Properties

to open the Internet Protocol (TCP/IP)

Properties window.

4.

Select

Obtain an IP address automatically

and

Obtain DNS server address automatically

.

5.

Click

OK

to save the TCP/IP settings and close the Internet Protocol (TCP/IP) Properties window.

6.

Step through to close the remaining windows and exit.

7.

To verify the IP address, open a command prompt window using the

Start

button from the Taskbar

on your desktop.

8.

Type

ipconfig

and press

Enter

to display the IP configuration.

9.

To renew the IP address, type

ipconfig /renew

and press

Enter

. A new IP address for your

computer will display.

10.

Type

exit

and then press

Enter

to return to Windows.

If you still cannot access the Internet, contact your service provider.

Setting Up a Wireless Network Connection

B

SVG6x82 Series Wireless Voice Gateway

•

User Guide

10

590934-001-a

Setting Up a Wireless Network

Connection

You must have computer access to a high-speed Internet service to set up a wireless network

connection or connect wireless devices to the SVG6x82. Also, make sure the SVG6x82 and your

computer are connected through an Ethernet connection. Choose one of the following two options to set

up your wireless network connection:

•

Setting Up a Wireless Network on Your Computer

•

Using the WPS Pairing Button

After setting up your wireless network connection, check that the wireless network connection was set

up properly. See

Testing Your Wireless Network Connection

for more information.

Setting Up a Wireless Network on Your Computer

Note

: The steps for setting up a wireless network may differ slightly depending on the Windows

operating system installed on your computer. The following steps apply for Windows 7 systems.

1.

From the Windows taskbar, click

Start

button and then click

Control Panel

,

Network and Sharing

Center

.

2.

Click

Set up a new connection or network

.

3.

Click

Connect to the Internet

.

Note

: The

You are already connected to the Internet

message may appear. Ignore this message

and proceed with the next step.

4.

Click

Set up a new connection anyway

and then click

Wireless

.

5.

Scroll down and click the

MOTOROLA

wireless network name (see the

SSID

number listed on the

SVG6x82 gateway label).

6.

Enter

Network security key code

in the Security key field (see

Wi-Fi Security

code listed on the

SVG6x82 gateway label) and then click

OK

to complete the wireless network connection.

A Connected status message showing the wireless network connection should display.

7.

Close the Wireless Network Connection window.

Using the WPS Pairing Button

Note

: To use the WPS Pairing button option, your computer hardware must support WPS and also have

WPA security compatibility.

The WPS option automatically assigns a random wireless network name (SSID) and Wi-Fi Security Key to

the SVG6x82 and other WPS-enabled devices to connect to your wireless network.

1.

Power ON the gateway and other WPS-enabled devices that you want to connect to a wireless

network.

2.

Press and hold the WPS button located on the top of the SVG6x82 for five or more seconds.

3.

Press the WPS button on your WPS-enabled computer or other device.

4.

Repeat step 3 for each additional WPS-enabled device you are connecting to your wireless network.

4

Setting Up a Wireless Network Connection

B

SVG6x82 Series Wireless Voice Gateway

•

User Guide

11

590934-001-a

Testing Your Wireless Network Connection

Perform the following test to verify that the SVG6x82 and other wireless devices can connect to your

wireless network:

1.

If connected, disconnect the Ethernet cable from your computer and the SVG6x82.

2.

Open a web browser on your computer.

3.

Type a valid URL (for example,

www.motorola.com/us

) in the address bar, and then click or press

Enter

.

If the web page did not open, please contact your service provider for assistance.

Accessing the Gateway

B

SVG6x82 Series Wireless Voice Gateway

•

User Guide

12

590934-001-a

Accessing the Gateway

Use the SVG6x82 Modem Web Manager to view the various configuration settings and operational

status of the gateway.

Starting the Gateway Web Manager

Note

: Use the following default username and password to log on to the SVG6x82 Web Manager for the

first time. For network security purposes, it is recommended that you change the user name and

password after logging on. See

Changing the Default Password

for more information.

1.

Open any web browser on the computer connected to the SVG6x82.

2.

In the Address bar, type

for the Gateway Web Manager IP address, and

then press

Enter

. The gateway Login window displays.

3.

Type the default username and password. Both entries are case-sensitive.

Username:

admin

Password:

motorola

Figure 5 – SVG6x82 Login Window

4.

Click

Login

to open the SVG6x82 Web Manager. The SVG6x82 Status Connection page displays.

5