6

XWR-1750

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-UG-XWR-1750

Vers: 022515

LED Indicators:

Indicator

Description

Function

5GHz

FLASHING

Indicates the XWR-1750 is passing 5GHz

wireless data.

ON

Indicates a 5GHz wireless network is

configured and broadcasting.

OFF

Indicates there is no 5GHz wireless network

configured or the 5GHz radio is disabled.

2.4GHz

FLASHING

Indicates the XWR-1750 is passing 2.4GHz

wireless data.

ON

Indicates a 2.4GHz wireless network is

configured and broadcasting.

OFF

Indicates there is no 2.4GHz wireless network

configured or the 2.4GHz radio is disabled.

1-4 LAN LED

ON

Indicates a device is connected to the

Ethernet port number.

FLASHING

Indicates data packets are being transmitted

to the connected device.

Internet

LED

ON

Indicates the XWR-1750 is connected to

the ISP.

FLASHING

Indicates data packets are being transmitted

to the Internet

USB LED

ON

Indicates a USB enabled device is connected

and configured.

System LED

ON

Indicates the XWR-1750 is booting.

FLASHING

Indicates the XWR-1750 is operating normally.

OFF

Indicates the XWR-1750 will not boot.

Power LED

ON

Indicates power is applied to the XWR-1750.

OFF

Indicates power is not applied to the

XWR-1750.

Luxul LED

Unused at this time

7

User Guide

© 2015

Luxul. All Rights Reserved.

Other trademarks and registered trademarks are the property of their respective owners

NOTE:

If additional local ports are required, it is recommended that a Luxul

switch be used in conjunction with the XWR-1750.

2.1.2 Rear Panel

±

Antenna: 3 RPSMA Antenna ports for connecting 2.4/5GHz wireless Antennas.

±

Power: Power port used to connect the provided DC power supply.

±

WAN: 1 WAN RJ-45 Ethernet Port for connecting internet feed.

±

LAN: 4 LAN RJ-45 Ethernet Ports allowing for four local network connections.

±

Reset Button: Used for hard reset or factory default reset. To hard reset the router,

press and release the button. To reset to factory defaults, press and hold this button

for 15 seconds.

CAUTION:

Resetting the XWR-1750 to factory defaults will remove all

custom settings

XWR-1750 Rear Panel

2.2 System Requirements

±

Network Connections: 802.3 Ethernet Enabled Computer or 802.11a/b/g/n/ac

Wireless Enabled Computer

±

Web Browsers: Supported Web browser versions include I.E. 9, Firefox 25, Safari 5,

Chrome 30, and up. The Web browser is used to configure the XWR-1750.

±

Internet: Broadband Internet Service (depending on the service provider, a separate

modem may be required)

2.3 Installation Requirements

±

Install the XWR-1750 in a stable/safe place to avoid any possible damage

±

Inspect the DC power adapter to ensure that it is correctly connected

and undamaged

±

To avoid electric shock, DO NOT open the XWR-1750 housing (no user serviceable

parts inside). Opening the XWR-1750 will void your warranty.

8

XWR-1750

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-UG-XWR-1750

Vers: 022515

±

It is recommended that the Grounding connection to the outlet is functioning

properly and the XWR-1750 is positioned away from direct sun light

±

Ensure there is sufficient space around the XWR-1750 for proper ventilation and heat

dissipation. It is recommended to have at least 4-6 inches around all sides.

2.4 XWR-1750 Installation

Before installing the XWR-1750, test the Internet connection to validate that it is

functioning properly. When Internet access has been confirmed, follow the steps below

for Router installation.

1. Connect the Internet cable to the XWR-1750 WAN port

2. Connect one of the XWR-1750 LAN port to a switch, access point, or computer.

3. Connect DC Power Adapter

4. Establish LAN or Wireless Connection

5. Connect a Wireless device to the 2.4GHz or 5GHz Wireless SSID.

NOTE:

Connect the included DC power adapter to the XWR-1750 first and

then to the AC outlet.

2.5 Default IP Address

The XWR-1750 default IP address is 192.168.0.1. This address can be changed. However,

for hassle free installation of other plug and play Luxul devices, it is recommended that

the default IP value be maintained.

2.6 Connecting a Client Device

Connect a client device to one of the XWR-1750 LAN ports or to a switch that is

connected to an XWR-1750 LAN port. Connect a wireless client device to one of the

wireless SSIDs (

Luxul17502G

or

Luxul17505G

). The DHCP server on the XWR-1750 is

configured by default. If your client device is set to obtain an address automatically, no

further configuration is required.

2.7 Verifying Connectivity

After automatic configuration of the TCP/IP parameters, the ping command can be used

to check connectivity between the XWR-1750 and the client device.

Windows Devices:

6. Select

Start >> Run.

Input

cmd

in the Run line then press enter.

9

User Guide

© 2015

Luxul. All Rights Reserved.

Other trademarks and registered trademarks are the property of their respective owners

7. At the newly opened command interface enter the following command: ping

192.168.0.1 and press enter. If connected properly, the system should report back a

result as follows: packets sent=4, packets received=4, packets lost=0. This means the

device is connected with a valid IP address.

3 CONFIGURATION

This chapter introduces the configuration of the XWR-1750 Enterprise Multi-WAN

Router functions via the Web-based management interface.

±

Quick Setup

±

Status

±

Network

±

Wireless

±

Guest Network

±

Firewall/Security

±

QoS

±

VPN

±

Administration

±

Tools

3.1 Quick Setup

The Quick Setup page allows you to configure the Primary Internet / WAN connec-

tion settings and the Local Network / LAN settings. This page is intended to get your

Internet connection up and running as quick and painless as possible.

3.1.1 Connection Type DHCP

This Connection Type option will automatically pull the WAN IP, WAN Subnet Mask,

WAN Gateway, WAN Primary DNS and WAN Secondary DNS from your ISP’s Modem.

Select the Menu

Quick Setup

and

Connection Type DHCP

from the dropdown to view

the following page:

10

XWR-1750

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-UG-XWR-1750

Vers: 022515

±

Internet/WAN:

Displays the WAN connection Options

w

Connection Type:

Select the desired WAN Connection Type. When set to DHCP,

the Router will pull all connection information automatically from the ISP’s

Modem. DHCP is the default setting.

w

Primary DNS:

Allows you to select the checkbox and manually configure a Primary

DNS Server IP Address. “DNS Assigned By ISP” is the default setting

w

Secondary DNS:

Allows you to select the checkbox and manually configure a

Secondary DNS Server IP Address. “DNS Assigned By ISP” is the default setting

w

Custom MAC Address:

Allows you to set a Custom MAC Address which allows the

Router to appear as a Computer to the ISP Modem. Some Modems will cache the

MAC Address of the first device used to setup Internet Service and cannot be reset

by the user. If this occurs you can clone that setup Device’s MAC Address to allow

the XWR-1750 to connect to the Modem.

w

Custom MTU:

Allows you to configure a Custom MTU setting. MTU (or Maximum

Transmission Unit), is the maximum packet size allowed on the network. Some ISPs

(usually DSL or Fiber) will require this value to be set if the Modem is in

Bridge mode.

±

After making any changes to the Connection Type, you must click the Save button

to Save your changes, then you must click the Reboot button for the changes to take

effect. You can click the Save button and proceed to other pages without losing your

configured changes.

3.1.2 Connection Type PPPOE

This Connection Type option requires a Username and Password that is provided by the

ISP and is typically used on Bridged DSL Modem connections. This type will automati-

cally pull the WAN IP, WAN Subnet Mask, WAN Gateway, WAN Primary

DNS and WAN Secondary DNS from the ISP’s Modem once the Router is

successfully Authenticated.