ice.net D-35 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

ice.net

D-35

Page 41 / 63 Scroll up to view Page 36 - 40

a channel that is at least five channels away from the other wireless network.

For instance, if another network is operating on channel 11, then set your

network to channel 6 or below. To change the channel, select the channel

from the drop-down list. Click “Apply Changes”. The change is immediate.

Securing your Wi-Fi® Network

Here are a few different ways you can maximize the security of your wireless

network and protect your data from prying eyes and ears. This section is

intended for the home, home office, and small office user. At the time of this

User Manual’s publication, there are two encryption methods available.

WEP (Wired Equivalent Privacy)

WEP (Wired Equivalent Privacy) is a common protocol that adds security to

all Wi-Fi compliant wireless products. WEP was designed to give wireless

networks the equivalent level of privacy protection as a comparable wired

network. (For Sweden and Denmark, default WEP Password for this unit is

“NMT35”. For Norway you should not type in any WEP Password, default

WEP Password is blank.)

WPA (Wi-Fi Protected Access)

WPA (Wi-Fi Protected Access) is a new Wi-Fi standard that was designed to

improve upon the security features of WEP. To use WPA security, the drivers

and software of your wireless equipment must be upgraded to support WPA.

These updates will be found on the wireless vendor’s website. There are two

types of WPA security, WPA-PSK (no server) and WPA (with radius server).

WPA-PSK (no server) uses what is known as a pre-shared key as the

network key. A network key is basically a password that is between eight and

63 characters long. It can be a combination of letters, numbers, or characters.

Each client uses the same network key to access the network. Typically, this

is the mode that will be used in a home environment.

Page 42 / 63

Advanced Wireless Settings

To access additional features of advanced wireless settings, select “Advanced ->

Wireless Setting” tab.

Wireless On

Check the box to enable the wireless function. If you do not want to use

wireless WiFi network function, uncheck the box to disable all the wireless

functions.

SSID Broadcast On

Check this option if you would not like the SSID of your wireless network to be

broadcasted by the D35. If this option is checked, the SSID of the D35 will not

be seen by Site Survey utilities so your wireless clients will have to know the

SSID of your D35 in order to connect to it.

Turn Access Control On (WiFi MAC Filtering)

Check this option if you like to use Access Control (WiFi MAC Filtering) Filters

Page 43 / 63

to allow or deny LAN (Local Area Network) computers by their MAC addresses

from accessing the WiFi Network. You can either manually add a MAC address

or select the MAC address from the list of WiFi client table that are currently

connected to the Broadband Router.

Maintenance: Router Status

Clicking on the header of the “Router Status” tab will take you to the “Router

Status” header page. A quick description of the functions can be found here.

1. IP Address

The “IP address” is the internal IP address of the Modem. The default IP

address is “192.168.0.1”. To access the web based Advanced User Interface,

type this IP address into the address bar of your browser. This address can

be changed if needed.

2. Subnet Mask

This is a unique, advanced feature of your Nordisk Mobiltelefon Modem. It is

possible to change the subnet mask if necessary; however, do NOT make

changes to the subnet mask unless you have a specific reason to do so. The

default setting is “255.255.255.0”.

Page 44 / 63

From this page, users can see all settings associated with the Modem’s router

network functions. These functions include:

Account Name and Firmware Version

WAN Port: MAC Address, IP Address, DHCP choice, IP Subnet Mask

and Domain Name Server Address

LAN Port: MAC Address, IP Address, DHCP choice and IP Subnet

Mask

Wi-Fi Port *: SSID, Region, Channel, Mode, Wireless AP status

(ON/OFF) and Broadcast Name status (ON/OFF)

Users can click the button “Show Statistic” to see a graphic display of the

router performance.

Configuring Port Forwarding

Clicking on the header of the “Port Forwarding” tab will take you to the “Port

Forwarding” header page. This function will allow you to route external

(Internet) calls for services such as a web server (port 80), FTP server (Port

21), or other applications through your Router to your internal network. Since

your internal computers are protected by a firewall, computers outside your

network (over the Internet) cannot get to them because they cannot be “seen.”

A list of common applications has been provided in case you need to configure

the “Port Forwarding” function for a specific application. You will need to

contact the application vendor to find out which port settings you need.

Page 45 / 63

Note

: This advanced feature should be employed by advanced users only.

Disable Port Forwarding

To disable Port Forwarding, check the box “Disable Port Forwarding”.

Entering Settings into the Port Forwarding

To enter settings, select the service from the dropdown box “Service Name”.

You will see a list of common applications (FTP, HTTP, Net-Meeting…).

Select the desired application enter the IP address in the space provided for

the internal (server) machine and click “Add”. In the pop up screen, enter the

port(s) required to pass, select the port type (TCP or UDP), and click “Apply

Changes”. Each inbound port entry has two fields with five characters

maximum per field that allows a start and end port range, e.g. [xxxxx]-[xxxxx].

For each entry, you can enter a single port value by filling in the two fields with

the same value (e.g. [7500]-[7500]) or a wide range of ports (e.g. [7500]-

[9000]). If you need multiple single port values or a combination of ranges and

a single value, you must use multiple entries up to the maximum of 20 entries

(e.g. 1. [7500]-[7500], 2. [8023]-[8023], 3. [9000]-[9000]). You can only pass

one port per internal IP address. Opening ports in your firewall can pose a

security risk. You can enable and disable settings very quickly. It is

recommended that you disable the settings when you are not using a specific

application.

Entering Settings into the Packet Forwarding

To enter settings, select Packet/Port Forwarding tab. Enter the IP address in

the space provided for the internal (server) machine. Select the port type (TCP

or UDP), enter source port number of incoming packet, enter destination port

number of forwarded packet. You can only pass one port per internal IP

address. Click “APPLY” button. Opening ports in your firewall can pose a

security risk. It is recommended that you disable the settings when you are not

using a specific application

Rate

Popular ice.net Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share