1. Home
    2. /
  2. Manuals
    3. /
  3. ice.net
    4. /
  4. D-35
    5. /
  5. 5
Page 21 / 63 Scroll up to view Page 16 - 20
1.5
Click “OK”.
Step 2
│
Connecting the Modem to your PC
2.1.
Turn off both the EV-DO modem and your PC.
2.2.
Connect the included USB Cable to the USB port on your PC.
2.3.
The Modem cable select switch, located between Ethernet and USB
connectors, should be set to USB.
2.4.
Connect other end of the USB Cable to USB port on the Modem.
2.5.
Connect the included Power Adapter to Power connector of EV-DO
modem.
2.6.
Connect the other end of Power Adapter to an electrical outlet.
2.7.
Power on EV-DO modem.
20
Page 22 / 63
Step 3
│
Window Device Setup
3.1
Power ON the PC. After the boot-up process, you will see “Found New
Hardware” screen appears. Select Next to install USB
21
3.2
Select “Continue Anyway”.
3.3
Press “Finish” to complete the process.
Page 23 / 63
3.4
The Diagnostic Port
will be detected on your PC. Select Next to install.
3.5
Select “Continue Anyway”.
3.6
Press “Finish” to complete the process.
22
Page 24 / 63
Connecting to Data Service with USB connection
After USB driver has been installed, you must use AxessManager
to configure
and connect the Modem to the network. Please refer to AxessManager
Operational Guide chapter for detailed instructions. Make sure the Modem
selector switch is set to USB position before attempting the connection.
Normally Windows OS will automatically detect your Modem USB
connection after you have installed AxessManager
. If for some reasons Windows
OS failed to complete this task, you may need to perform the following
steps after installing AxessManager
to fully configure your Modem in USB mode.
1.
Verify in Network Connection window that
USB connection has been created in “Dial up” section.
The connection name is set by your service provider
(default name is 1xEvDO). You can also find the
connection name in AxessManager utility, USB
Connection Profile tab
2.
If no USB connection appears in Dial up
section, go to AxessManager utility, USB Connection
Profile tab, highlight the connection name your service
provider has created, click
Edit
, insert user-ID “cdma”,
password “cdma” and dial #777. Click OK to accept the
set up. This will add the connection to the Network
Connection window, select Dial up connection.
3.
In very rare cases, Windows OS may associate
the wrong modem to your Dial up connection. To verify,
right click on the Dial up connection name in step 1
above and select
Properties
. You should see the
Axesstel USB Modem selected and the correct dial
number entered. If notupdate the fields with correct
value.
23
Page 25 / 63
Connection Using Ethernet (RJ-45) Ports
Although the Modem comes with drivers and enabling software, you don’t have
to install and use them if you simply want to connect to the Internet through the
Ethernet (RJ-45) ports.
Your modem has been pre-activated in the Nordisk Mobiltelefon network.
Connect your computer with the Modem using the provided Ethernet (RJ-45)
cable and you are ready to use the Internet.
Configuring Your PC
The Modem’s Ethernet is configured with DHCP by default. This means that IP
address of your PC is automatically assigned by the EV-DO Modem. If for some
reasons, the PC’s cannot get IP address and cannot make connection to Internet,
use the following steps to check the TCP/IP setting of your “Local Area
Connection”.
1. Click the Start button, select
Settings, and select Control Panel.
Click on “Network and Internet
Connection” icon.
NOTE:
DHCP stands for Dynamic Host Configuration Protocol. Your Modem has
a built-in DHCP server. The DHCP server will automatically assign an IP
address to the computers on the LAN. Be sure to set each client PC’s
TCP/IP settings to “obtain an IP address automatically”.
24

Rate

4.5 / 5 based on 2 votes.

Popular ice.net Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top