1. Home
    2. /
  2. Manuals
    3. /
  3. Hitron Technologies
    4. /
  4. CVE-30360
    5. /
  5. 5
Page 21 / 98 Scroll up to view Page 16 - 20
21
HITRON CVE-30360 USER’S GUIDE
INTRODUCTION
The CVE-30360 has a built-in DHCP server that, when active, assigns IP addresses
to computers on the LAN. When the DHCP server is active, you can get an IP
address automatically. The DHCP server is active by default.
If your computer is configured to get an IP address automatically, or if you are not
sure, try to log in to the CVE-30360 (see
Logging into the CVE-30360
on page
13
).
If the login screen displays, your computer is already configured correctly.
If the login screen does not display, either the CVE-30360’s DHCP server is not
active or your computer is not configured correctly. Follow the procedure in
Manual IP Address Setup
on page
12
and set your computer to get an IP
address automatically. Try to log in again. If you cannot log in, follow the manual
IP address setup procedure again, and set a specific IP address as shown. Try
to log in again.
NOTE:
If you still cannot see the login screen, your CVE-30360’s IP settings may
have been changed from their defaults. If you do not know the CVE-30360’s
new address, you should return it to its factory defaults. See Resetting the
CVE-30360 on page 14. Bear in mind that ALL user-configured settings are
lost.
1.4.1
MANUAL IP ADDRESS SETUP
By default, your CVE-30360’s local IP address is
192.168.0.1
. If your CVE-30360 is
using the default IP address, you should set your computer’s IP address to be
between
192.168.0.2
and
192.168.0.254
.
NOTE:
If your CVE-30360 DHCP server is active, set your computer to get an IP
address automatically in step 5. The CVE-30360 assigns an IP address to
your computer. The DHCP server is active by default.
Take the following steps to manually set up your computer’s IP address to connect to
the CVE-30360:
NOTE:
This example uses Windows XP; the procedure for your operating system
may be different.
1
Click
Start
, then click
Control Panel
.
2
In the window that displays, double-click
Network Connections
.
3
Right-click your network connection (usually
Local Area Connection
) and click
Properties
.
4
In the
General
tab’s
This connection uses the following items
list, scroll
down and select
Internet Protocol (TCP/IP)
. Click
Properties
.
5
You can get an IP address automatically, or specify one manually:
Page 22 / 98
22
HITRON CVE-30360 USER’S GUIDE
INTRODUCTION
If your CVE-30360’s DHCP server is active, select
Get an IP address
automatically
.
If your CVE-30360’s DHCP server is not active, select
Use the following IP
address
. In the
IP address
field, enter a value between
192.168.0.2
and
192.168.0.254
(default). In the
Subnet mask
field, enter
255.255.255.0
(default).
NOTE:
If your CVE-30360 is not using the default IP address, enter an IP address
and subnet mask that places your computer in the same subnet as the CVE-
30360.
6
Click
OK
. The
Internet Protocol (TCP/IP)
window closes. In the
Local Area
Connection Properties
window, click
OK
.
Your computer now obtains an IP address from the CVE-30360, or uses the IP
address that you specified, and can communicate with the CVE-30360.
1.5
LOGGING INTO THE CVE-30360
Take the following steps to log into the CVE-30360’s GUI.
NOTE:
You can log into the CVE-30360’s GUI via the wireless interface. However, it
is strongly recommended that you configure the CVE-30360 via a wired
connection on the LAN.
1
Open a browser window.
2
Enter the CVE-30360’s IP address (default
192.168.0.1
) in the URL bar. The
Login
screen displays.
FIGURE 4:
Login
3
Enter the
Username
and
Password
. The default login username is
admin
, and
the default password is
password
.
Page 23 / 98
23
HITRON CVE-30360 USER’S GUIDE
INTRODUCTION
NOTE:
The Username and Password are case-sensitive; “admin” is not the same as
“Admin”.
4
Click
Login
. The
System Info
screen displays (see
The System Info Screen
on
page
30
).
1.6
GUI OVERVIEW
This section describes the CVE-30360’s GUI.
FIGURE 5:
GUI Overview
1.7
RESETTING THE CVE-30360
When you reset the CVE-30360 to its factory defaults, all user-configured settings are
lost, and the CVE-30360 is returned to its initial configuration state.
There are two ways to reset the CVE-30360:
TABLE 3:
GUI Overview
Primary
Navigation Bar
Use this section to move from one part of the GUI to another.
Secondary
Navigation Bar
Use this section to move from one related screen to another.
Main Window
Use this section to read information about your CVE-30360’s
configuration, and make configuration changes.
Page 24 / 98
24
HITRON CVE-30360 USER’S GUIDE
INTRODUCTION
Press the
RESET
button on the CVE-30360, and hold it in for ten seconds or
longer.
Click
LAN
>
Backup
. In the screen that displays, click the
Factory Reset
button.
The CVE-30360 turns off and on again, using its factory default settings.
NOTE:
Depending on your CVE-30360’s previous configuration, you may need to re-
configure your computer’s IP settings; see IP Address Setup on page 11.
Page 25 / 98
25
CABLE
2
CABLE
This chapter describes the screens that display when you click
Cable
in the toolbar.
2.1
CABLE OVERVIEW
This section describes some of the concepts related to the
Cable
screens.
2.1.1
DOCSIS
The Data Over Cable Service Interface Specification (DOCSIS) is a
telecommunications standard that defines the provision of data services) Internet
access) over a traditional cable TV (CATV) network.
Your CVE-30360 supports DOCSIS version 3.0.
2.1.2
IP ADDRESSES AND SUBNETS
Every computer on the Internet must have a unique Internet Protocol (IP) address.
The IP address works much like a street address, in that it identifies a specific
location to which information is transmitted. No two computers on a network can have
the same IP address.
2.1.2.1
IP ADDRESS FORMAT
IP addresses consist of four octets (8-bit numerical values) and are usually
represented in decimal notation, for example
192.168.1.1
. In decimal notation, this
means that each octet has a minimum value of 0 and a maximum value of 255.
An IP address carries two basic pieces of information: the “network number” (the
address of the network as a whole, analogous to a street name) and the “host ID”
(analogous to a house number) which identifies the specific computer (or other
network device).
2.1.2.2
IP ADDRESS ASSIGNMENT
IP addresses can come from three places:
The Internet Assigned Numbers Agency (IANA)

Rate

4.5 / 5 based on 2 votes.

Popular Hitron Technologies Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top