1. Home
    2. /
  2. Manuals
    3. /
  3. Hawking
    4. /
  4. HWRN2
    5. /
  5. 4
Page 16 / 136 Scroll up to view Page 11 - 15
7
LNK/ACT
Off
LAN port is not connected
Flashing
LAN activity (transferring or receiving data)
Back Panel
Item Name
Description
Antenna A to B
All are 3dBi dipole antennas.
Power
Power connector, connects to A/C power adapter.
Reset
Reset the router to factory default settings (clear all settings).
Press this button and hold for 10 seconds to restore all settings
to factory defaults.
LAN (1 – 4)
Local Area Network (LAN) ports 1 to 4.
MODEM
Wireless On/Off
Wide Area Network (WAN / Internet) port.
Switch the wireless radio on or off
Antenna A
Antenna B
Page 17 / 136
8
Chapter II: System and Network Setup
2-1 Build network connection
Please follow the following instructions to build the network connection
between your new WIRELESS router and your computers and other
network devices:
1.
Connect your xDSL / cable modem to the WAN port of router by
Ethernet cable.
2.
Connect all your computers and network devices (network-enabled
consumer devices other than
3.
computers, like game console, or switch / hub) to the LAN port of the
router.
4.
Connect the A/C power adapter to the wall socket, and then connect it
to the ‘Power’ socket of the router.
5.
Please check all LEDs on the front panel. ‘PWR’ LED should be
steadily on, WAN and LAN LEDs should be on if the computer /
network device connected to the respective port of the router is
powered on and correctly connected. If PWR LED is not on, or any
LED you expected is not on, please recheck the cabling, or jump to
‘4-2 Troubleshooting’
for possible reasons and solutions.
Page 18 / 136
9
2-2 Connecting to wireless broadband router by web browser
After the network connection is built, the next step you should do is
setup the router with proper network parameters, so it can work properly
in your network environment.
Before you can connect to the router and start configuration
procedures, your computer must be able to get an IP address
automatically (use dynamic IP address). If it’s set to use static IP address,
or you’re unsure, please follow the following instructions to configure
your computer to use dynamic IP address:
If the operating system of your computer is….
Windows 95/98/Me
- please go to section 2-2-1
Windows 2000
- please go to section 2-2-2
Windows XP
- please go to section 2-2-3
Windows Vista
- please go to section 2-2-4
2-2-1 Windows 95/98/Me IP Address setup:
1.
Click ‘Start’ button (it should be located at lower-left corner of your
computer), then click control panel. Double-click
Network
icon, and
Network
window will appear. Select ‘TCP/IP’, then click ‘Properties’.
Page 19 / 136
10
2. Select ‘Obtain an IP address from a DHCP server’ and then click ‘OK’.
2-2-2Windows 2000 IP address setup:
1. Click ‘Start’ button (it should be located at lower-left corner of your
computer), then click control panel. Double-click
Network and Dial-up
Connections
icon; click
Local Area Connection,
and
Local Area
Connection Properties
window will appear. Select ‘Internet Protocol
(TCP/IP)’ and then click ‘Properties’
Page 20 / 136
11
2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server
address automatically’, then click ‘OK’.

Rate

4.5 / 5 based on 2 votes.

Popular Hawking Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top