1. Home
    2. /
  2. Manuals
    3. /
  3. EDIMAX
    4. /
  4. AR-7266WnA
    5. /
  5. 3
Page 11 / 124 Scroll up to view Page 6 - 10
2
1.1. Features
ADSL2/2+ Compliance
•
Support downstream rates of up to 24Mbps and upstream rates of up to
1Mbps.
•
Compliant to ITU-T G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3 (ADSL2),
G.992.4 (splitterless ADSL2), G.992.5 (ADSL2+) for Annex A, B. (Annex A
and B are supported in different H/W platform)
•
Multiple Protocols over AAL5 (RFC 1483/2684).
•
PPP over AAL5 (RFC 2364).
•
PPP over Ethernet (RFC 2516).
Supports 802.11b/g/n Wireless Access Point
•
Complies with IEEE 802.11b/g/n standard.
•
High data rate – up to 300Mbps network speed.
•
Supports 64-bit/128-bit WEP, WPA-PSK and WPA2-PSK wireless security
functions.
•
Supports MAC address filtering.
Router
•
NAT (Network Address Translation) IP Sharing
•
Port Forwarding/Port Mapping
•
DMZ
•
VPN Pass Through (IPSec/PPTP/L2TP)
•
IP QoS
•
SPI Anti-DOS Firewall
•
DHCP Server and Client
Access Management
•
ACL (Access Control)
•
IP/MAC/Port Filter
•
UPnP (Universal Plug and Play)
•
SNMP
•
Dynamic DNS
Page 12 / 124
3
1.2. Minimum Requirements
The following devices are necessary to configure and use the ADSL2+ Router:
•
A PC with Pre-installed Ethernet Adapter (Required) and a Web-Browser
(Internet Explorer 4.0 or higher)
•
RJ-45 Ethernet crossover cable (Included in the package)
•
RJ-11 (ADSL Ready) phone Line
1.3. Package Content
•
One ADSL2+ Router (Annex A or B)
•
One Power Adapter (12VDC, 1A)
•
Two 3dBi Antenna
•
One RJ-45 Ethernet Cable (100 cm)
•
One RJ-11 Telephone Line (180 cm)
•
One Quick Installation Guide
•
One CD with EZmax Setup Wizard , Multi-languages QIG and User
Manual
Page 13 / 124
4
1.4. Hardware Placement
1.4.1. Rear Panel
Item Name
Description
Antenna A/B
These antennas are 3dBi dipole antennas.
Radio
ON/OFF
Switch the button to activate or deactivate the wireless
functions.
Reset / WPS
Reset the router to factory default settings (clear all settings)
or start WPS function. Press this button and hold for 10
seconds to restore all settings to factory defaults, and press
this button for less than 5 seconds to start WPS function.
1 - 4
The router’s 4 LAN ports are where you connect your LAN’s
PCs, printer servers, hubs and switches etc.
ADSL
Connect the supplied RJ-11 telephone line to this port and
your ADSL/telephone network.
Power
Please plug the power adapter attached with the ADSL
Router to the power jack. The power adapter is 12VDC, 1A.
1.4.2. Front LEDs
On the router’s front panel there are LED lights that inform you of the router’s
current status. Below is an explanation of each LED and its description.
Page 14 / 124
5
LED
Light Status
Description
POWER (Green)
On
Router is switched on and correctly
powered.
WLAN (Yellow)
On
Off
Wireless LAN WPS is on.
Wireless LAN is disabled
Blinking
Wireless traffic is transmitting or receiving
ADSL (Green)
On
Connected to an ADSL DSLAN
successfully
Blinking
ADSL line is not connect to internet.
LAN LNK/ACT (Port 1-4)
On
The LAN cable is connected to the router
Off
No network connection.
Blinking
Network traffic transferring or receiving
through the LAN port
Page 15 / 124
6
2. Hardware Installation
Step 1. Connect the ADSL Line
Use the supplied RJ-11 telephone cable, connect the router from the ADSL port
to your telephone socket with an ADSL micro filter plugged in.
Step 2. Connect the router to your LAN network
Connect the router to your PC, hub or switch by attached the Ethernet cable to
the LAN port of the router.
Step 3. Connect the Power Adapter to the Router
Connect the power adapter to the power jack on the rear panel of the router and
switch on the power.
Step 4. Check the ADSL LED light status
Please check the ADSL LED on the front panel. This light indicates the status of
your ADSL broadband through your telephone line. If the light is on solid, you can
continue the setup. However, if the light is flashing, there is no broadband line
being detected. Therefore, please call your Internet Service Provider (ISP) and
inform them about the flashing ADSL light.
Step 5. Firewall settings.
Please turn off all personal firewall before you continue the setup as they might
block the communication of your PC and the router.
Note
：
You must use the power adapter shipped along with the router, do
NOT
use any other power adapter from other sources.

Rate

3.5 / 5 based on 2 votes.

Popular EDIMAX Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top