±1

D-Link DAP-1555 User Manual

Section ² - Configuration

If you select

WEP

encryption, the following screen will

show you your network key to enter on your wireless

clients.

Click

Save

to finish the Setup Wizard.

For

WEP

encryption, enter a Network Key exactly 5 or

13 characters long or exactly 10 or 26 characters using

0-9 and A-F.

Click

Next

to continue.

Downloaded from

www.Manualslib.com

manuals search engine

±±

D-Link DAP-1555 User Manual

Section ² - Configuration

This Wizard is designed to assist you in your wireless network setup. It will guide you through step-by-step instructions

on how to set up your wireless network and how to make it secure.

Select

PIN

to use your PIN number from your wireless

device to connect to your network.

For

PBC

configuration, skip to page 23.

Click

Connect

to continue.

Start WPS on the wireless device you are adding to you

wireless network to complete the setup.

Add Wireless Device With WPS

Downloaded from

www.Manualslib.com

manuals search engine

±²

D-Link DAP-1555 User Manual

Section ² - Configuration

Press down the Push Button on the wireless device you

are adding to your network to complete the setup.

Select

PBC

to use the Push Button Configuration to

connect to your network.

Click

Connect

to continue.

Downloaded from

www.Manualslib.com

manuals search engine

±³

D-Link DAP-1555 User Manual

Section ² - Configuration

Wireless Mode:

Enable Wireless:

Wireless Network

Name:

802.11 Band:

802.11 Mode:

The current wireless mode is set to Access Point, it

will create a wireless infrastructure network.

Check the box to enable the wireless function. If you

do not want to use wireless, uncheck the box to disable

all the wireless functions.

When you are browsing for available wireless

networks, this is the name that will appear in the list

(unless Visibility Status is set to Invisible, see below).

This name is also referred to as the SSID. For security

purposes, it is highly recommended to change from

the pre-configured network name.

Operating frequency band. Choose 2.4GHz for visibility

to legacy devices and for longer range. Choose 5GHz

for least interference.

If you choose 2.4GHz band, than select one of the

following:

802.11b Only

- Select if all of your wireless clients

are 802.11b.

802.11g Only

- Select if all of your wireless clients

are 802.11g.

802.11n Only

- Select only if all of your wireless clients

are 802.11n.

Mixed 802.11g and 802.11b

- Select if you are using

both 802.11b and 802.11g wireless clients.

Mixed 802.11n and 802.11g -

Select if you are using

both 802.11n and 802.11g wireless clients.

Mixed 802.11n, 802.11b, and 802.11g

- Select if you are using a mix of 802.11n, 11g, and 11b wireless clients.

If you choose 5GHz band, then select either

802.11a only

,

802.11n only

, or

Mixed 802.11n and 802.11a

.

Manual Configuration

Wireless Settings

Downloaded from

www.Manualslib.com

manuals search engine

±5

D-Link DAP-1555 User Manual

Section ² - Configuration

The Auto Channel Scan setting can be selected to allow the DAP-1555 to choose the channel with the least amount of

interference.

Indicates the channel setting for the DAP-1555. By default the channel is set to 6 for 2.4GHz band. The Channel can be

changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto

Channel Scan, this option will be greyed out.

Select the transmit rate. It is strongly suggested to select

Best (Auto)

for best performance.

Select the Channel Width:

Auto 20/40

- Select if you are using both 802.11n and non-802.11n wireless devices.

20MHz

- Select if you are not using any 802.11n wireless clients.

Select

Invisible

if you do not want the SSID of your wireless network to be broadcasted by the DAP-1555. If Invisible is selected,

the SSID of the DAP-1555 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your

DAP-1555 in order to connect to it.

Refer to page 65 for more information regarding the wireless security.

Enable the Wi-Fi Protected Setup feature.

Locking the wireless security settings prevents the settings from being changed by any new external registar using its PIN.

Devices can still be added to the wireless network using Wi-Fi Protected Setup. It is still possible to change wireless network

settings with Manual Wireless Network Setup, Wireless Network Setup Wizard, or an existing external WLAN Manager

Registar.

Shows the current value of the access point’s PIN.

Create a random number that is a valid PIN. This becomes the access point’s PIN. You can then copy this PIN to the user

interface of the registrar.

Restore the default PIN of the access point.

Resets Wi-Fi Protected Status to Not Configured. Vista WPS icon will only be displayed when the Wi-Fi Protected Status is

Not Configured.

Enable Auto

Channel Scan:

Wireless Channel:

Transmission Rate:

Channel Width:

Visibility Status:

Security Mode:

Enable:

Lock Wireless

Security Settings:

Current PIN:

Generate New PIN:

Reset PIN to

Default:

Reset to

Unconfigured:

Downloaded from

www.Manualslib.com

manuals search engine