IMPORTANT SAFETY INSTRUCTIONS

4042831 Rev A

vii

Service Warnings

WARNING: Avoid electric shock! Do not open the cover of this product. Opening or

removing the cover may expose you to dangerous voltages. If you open the cover, your

warranty will be void. This product contains no user-serviceable parts.

Check Product Safety

Upon completion of any service or repairs to this product, the service technician must perform safety

checks to determine that this product is in proper operating condition.

Protect the Product When Moving It

Always disconnect the power source when moving the apparatus or connecting or disconnecting

cables.

Telephone Equipment Notice

When using your telephone equipment, basic safety precautions should always be followed to reduce

the risk of fire, electric stock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry

tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger

telecommunication line cord.

SAVE THESE INSTRUCTIONS

20110316_Cable_Safety

20110316_Modem No Battery_Safety

United States FCC Compliance

4042831 Rev A

ix

United States FCC Compliance

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against such interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy. If not installed and used in accordance with the

instructions, it may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment OFF and ON, the user is encouraged to try to correct the interference

by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the service provider or an experienced radio/television technician for help.

Any changes or modifications not expressly approved by Cisco Systems, Inc., could void the

user's authority to operate the equipment.

The information shown in the FCC Declaration of Conformity paragraph below is a

requirement of the FCC and is intended to supply you with information regarding the FCC

approval of this device.

The phone numbers listed are for FCC-related questions only and not

intended for questions regarding the connection or operation for this device. Please contact your

service provider for any questions you may have regarding the operation or installation of this device.

Declaration of Conformity

This device complies with Part 15 of FCC

Rules. Operation is subject to the following

two conditions: 1) the device may not cause

harmful interference, and 2) the device must

accept any interference received, including

interference that may cause undesired

operation.

DOCSIS Residential Gateway

Model(s): DPC2320 EPC2320

Manufactured by:

Cisco Systems, Inc.

5030 Sugarloaf Parkway

Lawrenceville, Georgia 30044 USA

Telephone: 770 236-1077

Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.

United States FCC Compliance

x

4042831 Rev A

RF Exposure Statements

Note:

This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter. This equipment should be installed and operated with a minimum

distance of 7.9 inches (20 cm) between the radiator and your body.

US

This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1

(American National Standards Institute) limits. The evaluation was based in accordance with

FCC OET Bulletin 65C rev 01.01 in compliance with Part 2.1091 and Part 15.27. The minimum

separation distance from the antenna to general bystander is 7.9 inches (20 cm) to maintain

compliance.

Canada

This system has been evaluated for RF exposure for humans in reference to Canada Health

Code 6 (2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The

minimum separation distance from the antenna to general bystander is 7.9 inches (20 cm) to

maintain compliance.

EU

This system has been evaluated for RF exposure for humans in reference to the ICNIRP

(International Commission on Non-Ionizing Radiation Protection) limits. The evaluation was

based on the EN 50385 Product Standard to Demonstrate Compliance of Radio Base Stations

and Fixed Terminals for Wireless Telecommunications Systems with basic restrictions or

reference levels related to Human Exposure to Radio Frequency Electromagnetic Fields from

300 MHz to 40 GHz. The minimum separation distance from the antenna to general

bystander is 20 cm (7.9 inches).

Australia

This system has been evaluated for RF exposure for humans as referenced in the Australian

Radiation Protection standard and has been evaluated to the ICNIRP (International

Commission on Non-Ionizing Radiation Protection) limits. The minimum separation distance

from the antenna to general bystander is 20 cm (7.9 inches).

20100527 FCC DSL_Dom and Intl

CE Compliance

4042831 Rev A

xi

CE Compliance

Declaration of Conformity with Regard to the EU Directive 1999/5/EC

(R&TTE Directive)

This declaration is only valid for configurations (combinations of software, firmware and

hardware) supported or provided by Cisco Systems for use within the EU. The use of

software or firmware not supported or provided by Cisco Systems may result in the

equipment no longer being compliant with the regulatory requirements.

Note:

The full declaration of conformity for this product can be found at

.