IMPORTANT SAFETY INSTRUCTIONS

4036168 Rev B

vii

IMPORTANT SAFETY INSTRUCTIONS

1)

Read these instructions.

2)

Keep these instructions.

3)

Heed all warnings.

4)

Follow all instructions.

5)

Do not use this apparatus near water.

6)

Clean only with dry cloth.

7)

Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8)

Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9)

Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding-type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11)

Only use attachments/accessories specified by the manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from

tip-over.

13)

Unplug this apparatus during lightning storms or when unused for long periods of

time.

14)

Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as a power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

Power Source Warning

A label on this product indicates the correct power source for this product. Operate this product only

from an electrical outlet with the voltage and frequency indicated on the product label. If you are

uncertain of the type of power supply to your home or business, consult your service provider or your

local power company.

The AC inlet on the unit must remain accessible and operable at all times.

Ground the Product

WARNING: Avoid electric shock and fire hazard! If this product connects to coaxial

cable wiring, be sure the cable system is grounded (earthed). Grounding provides

some protection against voltage surges and built-up static charges.

IMPORTANT SAFETY INSTRUCTIONS

viii

4036168 Rev B

Protect the Product from Lightning

In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.

Verify the Power Source from the On/Off Power Light

When the on/off power light is not illuminated, the apparatus may still be connected to the power

source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged

into an AC power source.

Eliminate AC Mains Overloads

WARNING: Avoid electric shock and fire hazard! Do not overload AC mains, outlets,

extension cords, or integral convenience receptacles. For products that require battery

power or other power sources to operate them, refer to the operating instructions for

those products.

Provide Ventilation and Select a Location



Remove all packaging material before applying power to the product.



Do not place this apparatus on a bed, sofa, rug, or similar surface.



Do not place this apparatus on an unstable surface.



Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation

provides proper ventilation.



Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or

other objects on top of this product.



Do not block ventilation openings.

Protect from Exposure to Moisture and Foreign Objects

WARNING: Avoid electric shock and fire hazard! Do not expose this product to

dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as

vases, should not be placed on this apparatus.

WARNING: Avoid electric shock and fire hazard! Unplug this product before cleaning.

Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning

device (dust remover) to clean this product.

WARNING: Avoid electric shock and fire hazard! Never push objects through the

openings in this product. Foreign objects can cause electrical shorts that can result in

electric shock or fire.

Service Warnings

WARNING: Avoid electric shock! Do not open the cover of this product. Opening or

removing the cover may expose you to dangerous voltages. If you open the cover, your

warranty will be void. This product contains no user-serviceable parts.

IMPORTANT SAFETY INSTRUCTIONS

4036168 Rev B

ix

Check Product Safety

Upon completion of any service or repairs to this product, the service technician must perform safety

checks to determine that this product is in proper operating condition.

Protect the Product When Moving It

Always disconnect the power source when moving the apparatus or connecting or disconnecting

cables.

Telephone Equipment Notice

When using your telephone equipment, basic safety precautions should always be followed to reduce

the risk of fire, electric stock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry

tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger

telecommunication line cord.

SAVE THESE INSTRUCTIONS

20090915_Modem No Battery_Safety

United States FCC Compliance

x

4036168 Rev B

United States FCC Compliance

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against such interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy. If not installed and used in accordance with the

instructions, it may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment OFF and ON, the user is encouraged to try to correct the interference

by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the service provider or an experienced radio/television technician for help.

Any changes or modifications not expressly approved by Cisco Systems, Inc., could void the

user's authority to operate the equipment.

The information shown in the FCC Declaration of Conformity paragraph below is a

requirement of the FCC and is intended to supply you with information regarding the FCC

approval of this device.

The phone numbers listed are for FCC-related questions only and not

intended for questions regarding the connection or operation for this device. Please contact your

service provider for any questions you may have regarding the operation or installation of this device.

Declaration of Conformity

This device complies with Part 15 of FCC

Rules. Operation is subject to the following

two conditions: 1) the device may not cause

harmful interference, and 2) the device must

accept any interference received, including

interference that may cause undesired

operation.

DDR2200 Residential Gateway

Model(s): DDR2200

Manufactured by:

Cisco Systems, Inc.

5030 Sugarloaf Parkway

Lawrenceville, Georgia 30044 USA

Telephone: 678-277-1120

Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.

FCC Part 68

The Federal Communications Commission (FCC) of the United States restricts specific uses of

modems, and places registration responsibilities on both the manufacturer and the individual

user.

United States FCC Compliance

4036168 Rev B

xi

1

The modem may not be connected to a party line or to a coin-operated telephone.

2

Notification to the telephone company is no longer required prior to connecting

registered equipment, but upon request from the telephone company, the user shall tell

the telephone company which line the equipment is connected to as well as the

registration number and ringer equivalence number of the registered protective circuitry.

FCC information is printed on a label on the bottom of the modem.

This equipment complies with Part 68 of FCC Rules and the requirements adopted by the

ACTA. On the base unit of this equipment is a label that contains, among other information,

a product identifier in the format US: US:GEMDL01BDDR2200. If requested, this number

must be provided to the telephone company.

The REN is useful to determine the quantity of devices you may connect to your telephone

line and still have those devices ring when your telephone number is called. In most, but not

all areas, the sum of the REN of all devices connected to one line should not exceed five (5.0).

To be certain of the number of devices you may connect to your line, as determined by the

REN, you should contact your local telephone company to determine the maximum REN for

your calling area.

If your equipment causes harm to the telephone network, the telephone company may

discontinue your service temporarily. If possible, they will notify you in advance. If advance

notice is not practical, you will be notified as soon as possible. You will be informed of your

right to file a complaint with the FCC. Your telephone company may make changes in its

facilities, equipment, operations or procedures that could affect the proper functioning of

your equipment. If they do, you will be notified in advance to give you an opportunity to

maintain uninterrupted telephone service.

If you experience trouble with this telephone equipment, please contact the service provider

for information on obtaining service or repairs.

The telephone company may ask that you disconnect this equipment from the network until

the problem has been corrected or until you are sure that the equipment is not

malfunctioning.

This equipment may not be used on coin service provided by the telephone company.

Connection to party lines is subject to state tariffs.

IC (Industry Canada) Notice

Notice: The Industry Canada (formerly Canadian Department of Communications) label

identifies certified equipment. This certification means that the equipment meets certain

telecommunications network protective, operational, and safety requirements. The

department does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed

using an acceptable method of connection. In some cases, the company's inside wiring

associated with a single-line individual service may be extended by means of a certified

connector assembly (telephone extension cord). The customer should be aware that

compliance with the above conditions may not prevent degradation of service in some

situations.