Page 21 / 146 Scroll up to view Page 16 - 20
Chapter 3: Basic Installation
17
Factory Default Settings
Before configuring your, you need to know the following default settings.
Web Interface (Username and Password)
Username: admin
Password: admin
The default username and password are “
admin
” and “
admin
” respectively.
LAN Device IP Settings
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site
PPPoE
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are pre-set in the factory.
The default values are shown below.
LAN Port
WAN Port
IP address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP server function
Enabled
IP addresses for
distribution to PCs
100 IP addresses continuing from
192.168.1.100 through 192.168.1.199
The PPPoE function is
enabled
to automatically get the WAN
port configuration from the ISP,
but
you have
to set
the
username and password first.
Attention
If you ever forget the password to log in, you may press the RESET button up to
6 seconds to restore the factory default settings.
Attention
Page 22 / 146
Chapter 3: Basic Installation
18
Information from your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of
service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.
Gather the information as illustrated in the following table and keep it for reference
.
PPPoE
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service
Name, and Domain Name System (DNS) IP address (it can be automatically
assigned by your ISP when you connect or be set manually).
PPPoA
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and
Domain Name System (DNS) IP address (it can be automatically assigned by
your ISP when you connect or be set manually).
RFC1483 Bridged
VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.
RFC1483 Routed
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,
Gateway address, and Domain Name System (DNS) IP address (it is fixed IP
address).
IPoA
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,
Gateway address, and Domain Name System (DNS) IP address (it is fixed IP
address).
Page 23 / 146
Chapter 3: Basic Installation
19
Configuring with your Web Browser
Open your web browser, enter the IP address of your router, which by default is
192.168.1.254
, and click
Go
”, a user name and password window prompt will appear.
The default username and password
are “admin” and “admin”.
(See Figure 3.14)
Figure 3.14: User name & Password Prompt Widonw
Congratulation! You are now successfully logon to the 7402 ADSL Router!
Page 24 / 146
Chapter 4: Configuration
20
Chapter 4: Configuration
At the configuration homepage, the left navigation pane where bookmarks are provided links you directly
to the desired setup page, including:
Status
(ARP Table, Wireless Association Table, Routing Table, DHCP Table, PPTP Status,
IPSec Status, L2TP Status, Email Status, Event Log, Error Log, NAT Sessions and UPnP
Portmap)
Quick Start
Configuration
(LAN, WAN, System, Firewall, VPN, QoS, Virtual Server, Time Schedule and Advanced)
Save Config to FLASH
Language
(provides user interface in English and Deutsch languages)
Please see the relevant sections of this manual for detailed instructions on how to configure 7402 ADSL
Router.
Page 25 / 146
Chapter 4: Configuration
21
Status
ARP Table
This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping
of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the
MAC address of the network interface of your PCs to use with the router’s
Firewall – MAC Address
Filter
function. See the Firewall section of this manual for more information on this feature.
IP Address:
A list of IP addresses of devices on your LAN (Local Area Network).
MAC Address:
The MAC (Media Access Control) addresses for each device on your LAN.
Interface:
The interface name (on the router) that this IP Address connects to.
Static:
Static status of the ARP table entry:
~
no
” for dynamically-generated ARP table entries
~
yes
” for static ARP table entries added by the user

Rate

3.5 / 5 based on 2 votes.

Popular BEC Technologies Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top