Chapter 3: Basic Installation

17

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “

admin

” and “

admin

” respectively.

LAN Device IP Settings

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site

PPPoE

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory.

The default values are shown below.

LAN Port

WAN Port

IP address

192.168.1.254

Subnet Mask

255.255.255.0

DHCP server function

Enabled

IP addresses for

distribution to PCs

100 IP addresses continuing from

192.168.1.100 through 192.168.1.199

The PPPoE function is

enabled

to automatically get the WAN

port configuration from the ISP,

but

you have

to set

the

username and password first.

Attention

If you ever forget the password to log in, you may press the RESET button up to

6 seconds to restore the factory default settings.

Attention

Chapter 3: Basic Installation

18

Information from your ISP

Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of

service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.

Gather the information as illustrated in the following table and keep it for reference

.

PPPoE

VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service

Name, and Domain Name System (DNS) IP address (it can be automatically

assigned by your ISP when you connect or be set manually).

PPPoA

VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and

Domain Name System (DNS) IP address (it can be automatically assigned by

your ISP when you connect or be set manually).

RFC1483 Bridged

VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.

RFC1483 Routed

VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,

Gateway address, and Domain Name System (DNS) IP address (it is fixed IP

address).

IPoA

VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,

Gateway address, and Domain Name System (DNS) IP address (it is fixed IP

address).

Chapter 3: Basic Installation

19

Configuring with your Web Browser

Open your web browser, enter the IP address of your router, which by default is

192.168.1.254

, and click

“

Go

”, a user name and password window prompt will appear.

The default username and password

are “admin” and “admin”.

(See Figure 3.14)

Figure 3.14: User name & Password Prompt Widonw

Congratulation! You are now successfully logon to the 7402 ADSL Router!

Chapter 4: Configuration

20

Chapter 4: Configuration

At the configuration homepage, the left navigation pane where bookmarks are provided links you directly

to the desired setup page, including:

Status

(ARP Table, Wireless Association Table, Routing Table, DHCP Table, PPTP Status,

IPSec Status, L2TP Status, Email Status, Event Log, Error Log, NAT Sessions and UPnP

Portmap)

Quick Start

Configuration

(LAN, WAN, System, Firewall, VPN, QoS, Virtual Server, Time Schedule and Advanced)

Save Config to FLASH

Language

(provides user interface in English and Deutsch languages)

Please see the relevant sections of this manual for detailed instructions on how to configure 7402 ADSL

Router.

Chapter 4: Configuration

21

Status

ARP Table

This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping

of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the

MAC address of the network interface of your PCs to use with the router’s

Firewall – MAC Address

Filter

function. See the Firewall section of this manual for more information on this feature.

IP Address:

A list of IP addresses of devices on your LAN (Local Area Network).

MAC Address:

The MAC (Media Access Control) addresses for each device on your LAN.

Interface:

The interface name (on the router) that this IP Address connects to.

Static:

Static status of the ARP table entry:

~

“

no

” for dynamically-generated ARP table entries

~

“

yes

” for static ARP table entries added by the user