ADSL2+ 4-Port Ethernet USB Wireless-G Router - Easy Start

Safety Summary Messages

WARNING

Page 6 of 46

HIGH VOLTAGE

is used in the equipment. Make sure equipment is properly grounded

BEFORE opening. Failure to observe safety precautions may result in electric

shock to user.

CAUTION

Check voltages before connecting equipment to power supplies. Wrong

voltages applied may result in damage to equipment.

ADSL2+ 4-Port Ethernet USB Wireless-G Router - Easy Start

Page 7 of 46

Chapter 1 – Introduction

Thank you for purchase our 4-Port Ethernet USB Wireless-G ADSL2+ Router. The Wireless 4-

Port Router allows you to share high-speed broadband connection with multiple PC using a

single device wired or wireless.

The

4-Port

Ethernet

USB

Wireless-G

ADSL2+

Router

can

be

connected

to

any

computer/notebook with a 10/100 Base-T Ethernet card or USB port for wired connection or an

IEEE 802.11b/g Wireless adapter. The Ethernet ports have Auto MDI/MDIX feature which can

allows both cross or straight UTP cable to be utilized. The Wireless 4-port Ethernet Router has

an in-built IEEE802.11g Wireless LAN Access Point for wireless connectivity.

This documentation assumes that you have already installed an Ethernet card or a wireless

adapter on your computer/notebook

1.1

Minimum Requirements

•

Pentium

®

MMX 233MHz

•

A CD-ROM Drive

•

Ethernet card installed with TCP/IP Protocol (required only if you are connecting

to the ETHERNET port of your ADSL Router)

•

USB port (Required if you are connecting to the USB Port of your ADSL Router)

•

IEEE 802.11b/g Wireless adapter (Required if you are connecting to the Wireless

Access Point of the router)

•

Host Operating Systems support for USB:

- Windows® 98 Second Edition

- Windows® Me

- Windows® 2000

- Windows® XP

- Windows® XP x64 Edition

- Macintosh OS 10.2 & above

•

OS independent for Ethernet

•

Web Browser support:

- Microsoft Internet Explorer 4.0 (or later versions)

- Netscape® Navigator 3.02 (or later versions)

ADSL2+ 4-Port Ethernet USB Wireless-G Router - Easy Start

1.2

ADSL Router Package

ig 1-1

below shows the ADSL Router Package. For any missing items, please contact your

ireless Router

Easy Start Manual

Utility CD

Cat 5 Ethernet Straight Cable

USB Cable

Telephone Cable RJ-11

V Power Adapter

POTS-Splitter (Optional)

Figure 1-1 : ADSL Router Package

Depending on your country of purchase, your package may or may not come with a POTS

F

dealer immediately.

W

Page 8 of 46

9

Splitter. The POTS Splitter is required if you are connecting a Telephone Set to the Ethernet

Modem. Please refer to

Chapter 2 Section 2.2 - Connecting to the ADSL Line

for details.

POTS-Splitter can also be purchased from your dealer.

ADSL2+ 4-Port Ethernet USB Wireless-G Router - Easy Start

1.3

ADSL Router Overview

1.3.1 Front Indicators

Fig 1-2

Figure 1-2 : Front Indicators

shows the front indicators of the ADSL Router.

Page 9 of 46

1. Pow

Lights up

when power is supplied to the ADSL Router.

er

2. Ethernet(E1 - E4)

Lights up

when the Ethernet cable is properly connected

from your ADSL Router to the Ethernet Card.

Flickers

when the ADSL is transmitting/receiving data.

3. Wireless

.

Flickers

when the Wireless LAN is operational

4.

USB

Lights up

when the USB cable is properly connected

from your ADSL Router to the USB slot.

Lights Off

when the USB cable is not connected or it is properly

disconnected.

5.

DSL

n no Telephone jack (RJ-11) is connected.

Lights off

whe

Flickers

when the ADSL Router is trying to establish a

connection with the ADSL Service Provider (Training).

Steady Green LED.

Lights up

when the ADSL

connection is established.

6. Internet

hen

the

PPP

connection

is

Green LED

lights up

w

established.

Lights off

when no PPP connection.

4

6

3

5

1

2

ADSL2+ 4-Port Ethernet USB Wireless-G Router - Easy Start

1.3.2 Back Panel

panel indicators of the ADSL Router.

Figure 1-3 : Back Panel Indicators

Fig 1-3

shows the back

Page 10 of 46

1.

DSL

Connect the telephone jack (RJ-11) to your Telephone

Wall Socket (DSL line).

2.

USB

your PC’s USB slot.

Connect the USB jack to

3.

RESET

set button

To reset the ADSL Router, simply press the re

for about 10 seconds

(all customised settings that you

have saved will be lost!).

4.

ETHERNET(E1-E4)

I/MDIX

Ethernet

jack

(RJ-45)

10/100 Base-T Auto-MD

to connect to your PC’s Ethernet

Network card or

Ethernet Hub / Switch.

5.

DC 9V

r Adapter that comes with your

To connect to the Powe

package.

6.

POWER SWITCH

nwards to switch ON and lift upwards to switch

Push dow

OFF.

7.

RF Antenna

.4Ghz Wireless Antenna.

180

°

2

7

4

E1

5

6

3

1

2