1. Home
    2. /
  2. Manuals
    3. /
  3. Axesstel
    4. /
  4. MV600
    5. /
  5. 7
Page 31 / 58 Scroll up to view Page 26 - 30
30
Antenna + 1 bar
Low signal (-111
≤
sig. < -103 dBm )
Antenna + 2 bars
Medium-Low (-103
≤
sig. < -98 dBm)
Antenna + 3 bars
Medium signal (-98
≤
sig. < -93 dBm)
Antenna + 4 bars
Medium-high (93
≤
sig. < -88 dBm)
Antenna + 5 bars
Strongest signal (
≥
-88 dBm)
2. Battery Icon
OFF
No battery
Blinking red
Battery error or very low
Blue empty battery
Battery low level
Blue with 1 bar
Battery level 25%
Blue with 2 bars
Battery level 50%
Blue with 3 bars
Battery level 75%
Blue with 4 bars
Battery level close to 100%
Progressing 1- 4 bars
Battery is charging
3. Network Connection Icon
This icon shows the wired network connection mode of your Modem. Only one
mode can be used at a time.
OFF
No computers connected to Modem
Ethernet
RJ-45 port or Wi-Fi is in use
USB
USB port is in use
COM
COM port is in use
Note that there is a USB/Ethernet switch in the front of the Modem to select
which preferred mode for your connected computers. The COM mode can only
be activated from the "Menu" window.
4. Air Interface Icon
This icon informs you that the Modem is tuned to a 1x or EV-DO wireless
network. By default your Modem is programmed to search and use EV-DO
network. If unavailable, the Modem will try to search for a 1x network.
OFF
No network available, no service
EV-DO
EV-DO network is available
1xRTT
1X network is available
Page 32 / 58
31
5. Activity Icon
This icon indicates data activity between your Modem and the network.
OFF
No data activity
Blinking arrows
Data passing through your Modem
Steady arrows
Modem is in connect or dormant state
6. Info Text Messages
There are various Info messages displayed in this window. These messages
inform you various statuses of your Modem.
No Device
No devices connected to Modem
Searching…
Your Modem is searching EV-DO or
1X networks for services
No Service
Your Modem cannot detect any
network after search completed
Ready
Your Modem is ready for network
connection
Device Detected
Connected
Your Modem is connected to the
network
Connected
(Dormant)
Your Modem is connected to the
network but is inactive
Battery Low
Battery Error
7. Connect/Disconnect Button
This button allows you to connect or disconnect your Modem to the network. It
will toggle between two states Connect and Disconnect. The Disconnect button
appears only when your Modem is currently in the Connected or Connected
(Dormant) modes. This allows you to turn off the sessions by disconnecting your
Modem from the service network. In all other Modem modes, the Connect
button will appear. Note that although the Connect button appears, the Info Text
message must show “Ready” before you can connect to the network.
8. Menu/X/- Buttons
The Menu button gives you access to additional advanced Modem setting and
configuration such as Network Setup, Options and Status selection. The X
button exits AxessManager utility. Note that exiting the utility does not mean
Page 33 / 58
32
turning off your Modem. For example, if you exit the utility while the Modem is in
Connected or Connected (Dormant) mode, other computers can be plugged in
one of the ports and use the service. The - button allows you to minimize
AxessManager utility into Window tray.
Using the Menu Window
The Menu window is the main Interface that gives you access to more advanced
settings of your Modem. The Menu window is a stand-alone, pop-up window that
appears after you click the Menu button in the AxessManager main window. Once
you enter the Menu window, navigating to different tabs may result in subsequent
window pop-up to allow different configurations and settings of your Modem. In
the sections below, you will see each tab's functionality and operation.
1. About Tab
This tab informs you the basic details of your Modem. There are no further
actions needed in this tab. There is a slight difference in appearance when your
Modem is configured with Ethernet setting. When it occurs, About tab also
informs you the SW version of the Linux SW used to handle the Ethernet
function.
2. General Tab
This tab allows you to specify the system selection of your Modem. It also let
you choose the COM port setting.
Page 34 / 58
33
A. System Selection
This drop down menu lets you specify the wireless network that your
Modem will scan and seek service from. There are 4 modes for which
your Modem can operate:
•
EV-DO only
•
EV-DO and 1xRTT
•
1xRTT only
•
Not available
Note that EV-DO allows broadband high speed (up to 3.1 Mbps) while
1xRTT only supports up to 153 kbps. The default setting of your Modem
is set by your service provider and is normally "EV-DO and 1xRTT". In
this case, your Modem will attempt to get service first in EV-DO mode. If
EV-DO is unavailable then it will automatically switch to 1xRTT. We
recommend you leave this setting as set by your service provider.
B. Disable Automatic USB Port Search
This check lets you disable the automatic COM port assignment to use
for your computer USB and COM connections with the Modem. If
selected, a drop down menu with a list of available COM ports will
appear and you will need to specify the port number from that list.
Page 35 / 58
34
3. Status Tab
This tab shows you various performance statuses of your Modem. There are no
further actions needed in this tab.
4. USB Connection Profile Tab
This tab lets you define and manage the USB connection of your Modem. You
only have to specify items in this tab if you choose to connect and operate your
computer with the Modem via the USB port. Note that there is only one USB
port on the Modem hence there is only one single user who can use the Modem
in this mode. In normal operation, there are two USB connection profiles
predefined: one for EV-DO connection and one for 1xRTT connections. These
two profiles are included in the Install CD and downloaded to your PC during
the installation process.

Rate

4 / 5 based on 1 vote.

Popular Axesstel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top