1. Home
    2. /
  2. Manuals
    3. /
  3. Axesstel
    4. /
  4. MV430i
    5. /
  5. 5
Page 21 / 58 Scroll up to view Page 16 - 20
20
1.5
Click “OK”.
Step 2
│
Connecting the Modem to your PC
2.1.
Turn off both the EV-DO modem and your PC.
2.2.
Connect the included USB Cable to the USB port on your PC.
2.3.
The Modem cable select switch, located between Ethernet and USB
connectors, should be set to USB.
2.4.
Connect other end of the USB Cable to USB port on the Modem.
2.5.
Connect the included Power Adapter to Power connector of EV-DO modem.
2.6.
Connect the other end of Power Adapter to an electrical outlet.
2.7.
Power on EV-DO modem.
Page 22 / 58
21
Step 3
│
Window Device Setup
3.1
Power ON the PC. After the boot-up process, you will see “Found New
Hardware” screen appears. Select Next to install USB
3.2
Select “Continue Anyway”.
3.3
Press “Finish” to complete the process.
Page 23 / 58
22
3.4
Axesstel Diagnostic Port
will be detected on your PC. Select Next to
install.
3.5
Select “Continue Anyway”.
3.6
Press “Finish” to complete the process.
Page 24 / 58
23
Connecting to Data Service with USB connection
After USB driver has been installed, you must use AxessManager
to configure
and connect the Modem to the network. Please refer to AxessManager
Operational Guide chapter for detailed instructions. Make sure the Modem
selector switch is set to USB position before attempting the connection.
Normally Windows OS will automatically detect your Modem USB connection after
you have installed AxessManager
. If for some reasons Windows OS failed to
complete this task, you may need to perform the following steps after installing
AxessManager
to fully configure your Modem in USB mode.
1.
Verify in Network Connection window that
USB connection has been created in “Dial
up” section. The connection name is set by
your service provider (default name is
1xEvDO). You can also find the connection
name in AxessManager utility, USB
Connection Profile tab
2.
If no USB connection appears in Dial up
section, go to AxessManager utility, USB
Connection Profile tab, highlight the
connection name your service provider has
created, click
Edit
and
OK
to accept the
setup. This will add the connection to the
Network Connection window.
3.
In very rare cases, Windows OS may
associate the wrong modem to your Dial up
connection. To verify, right click on the Dial
up connection name in step 1 above and
select
Properties
. You should see the
Axesstel USB Modem selected and the
correct dial number entered. If not, update
the fields with correct value.
Page 25 / 58
24
Connection Using Ethernet (RJ45) Ports
Although the Modem comes with drivers and enabling software, you don’t have to
install and use them if you simply want to connect to the Internet through the
Ethernet (RJ-45) ports, assuming that your Modem has been activated with the
network
If you have MV400R-series, first go to AxessManager Operation Guide to
authenticate and configure your RUIM (if needed) before returning to the below
instructions.
Configuring Your PC
The Modem’s Ethernet is configured with DHCP by default. This means that IP
address of your PC is automatically assigned by the EV-DO Modem. If for some
reasons, the PC’s cannot get IP address and cannot make connection to Internet,
use the following steps to check the TCP/IP setting of your “Local Area
Connection”.
1. Click the Start button, select Settings,
and select Control Panel. Click on
“Network and Internet Connection” icon.
NOTE:
DHCP stands for Dynamic Host Configuration Protocol. Your Modem has
a built-in DHCP server. The DHCP server will automatically assign an IP
address to the computers on the LAN. Be sure to set each client PC’s
TCP/IP settings to “obtain an IP address automatically”.

Rate

4 / 5 based on 1 vote.

Popular Axesstel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top