Axesstel D8190AF Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Axesstel

D8190AF

Page 6 / 26 Scroll up to view Page 1 - 5

CDMA 1xEV-DO Wireless Broadband Modem

AXW-D800 / AXW-D1900

- 6 -

Connecting the World Now

Safety Precaution

1. Avoid placing the unit in a dusty location, or near a source of gas or fire.

2. Do not shake, hit or drop the unit.

3. To clean the unit, use only a soft, dry cloth. The chemicals in alcohol,

benzine or acetone can damage the surface of the unit.

4. Do not twist or pull the cord out of the unit.

5. Do not disassemble the phone.

6. DO NOT use the power adapter if the power cord is damaged or the

unit has been dropped or damaged in any way.

7. Only use the power adaptor provided by Axesstel.

Do not use the

Axesstel adapter for any other purpose.

8. Use only the antenna provided with the unit.

Do not use the antenna

for any other purpose.

9. Do not use the unit near water, for example, near a bathtub, sink, wet

basement, or swimming pool.

NOTE: The input voltage and the shape of the plug on this phone may

vary from country to country.

Basic Installation

1. Connect the antennas on the connectors of each side of the unit.

2. Connect the EV-DO modem to computer using RJ-45 Ethernet Cable

(CAT 5) or USB cable.

3. Move the connection selector switch to USB or Ethernet depending on

which cable you are using.

4. Connect the power adaptor to the DC 9V socket of the EV-DO modem.

5. Plug the AC adaptor into an appropriate electrical wall outlet.

Wall mounting…

1. Mark two mounting holes on the wall.

2. Drill two holes at the marked locations.

3. Tighten the screws until the head is about 5mm from the wall.

4. Hang the unit on the screw using the two holes in the back.

5. Push the unit down until the unit is firmly locked into place.

Page 7 / 26

CDMA 1xEV-DO Wireless Broadband Modem

AXW-D800 / AXW-D1900

- 7 -

Connecting the World Now

Getting to know the EV-DO modem

Power Switch

Power Switch is located on the front side of the EV-DO modem.

Turn on the unit by moving switch to ON position (O). Turn off the unit by

moving switch to OFF position (|).

NOTE: When you turn on the EV-DO modem, it automatically searches for

service signal. When it successfully acquires service signal, the

signal LED turns to green, orange or red depending on signal

strength.

Connection Type Switch

Axesstel Wireless 1xEV-DO Modem lets you choose type of connection.

Connection Type Switch is located between Ethernet port and USB port.

Set this switch to Ethernet or USB depending on type of connection you

are using.

LED Indicators

LED

Color

Indicates

Green

Power is on

Power

Off

Power is off

Green

Excellent signal level

Orange

Good signal level

Red

Poor signal level

Signal

Off

No signal or service is present

Green

Connected to the CDMA network

Connect

Off

Not connected

Green

PC connected to the modem by Ethernet

Blinking

Indicates data activity

Ethernet

Off

No PC connected to the modem by Ethernet

Page 8 / 26

CDMA 1xEV-DO Wireless Broadband Modem

AXW-D800 / AXW-D1900

- 8 -

Connecting the World Now

Connection using Ethernet port

1. Power off the unit before connecting the cables.

2. Connect CAT-5 Ethernet cable to Ethernet port of EV-DO Modem.

3. Connection type switch next to the Ethernet port should be set to

Ethernet.

If not, slide the switch toward the Ethernet port.

4. Connect other end of Ethernet cable to the RJ-45 connector of

Ethernet network adapter or a network device.

5. Connect the Power Adapter to the power connector of EV-DO modem.

Plug the AC plug into a power outlet.

6. Turn the power ON, using the power switch next to the power jack.

The LED labeled “Power” light on.

7. Wait for few seconds for EV-DO modem to search for the service.

The

LED labeled “Signal” turns to Red, Orange, or Green when signal is

acquired.

Configuring Your PC

The EV-DO modem’s Ethernet is configured with DHCP by default.

This

means that IP address of your PC is automatically assigned by the EV-DO

modem.

If the PC’s cannot get IP address and cannot make connection to internet.

Check the TCP/IP setting of your “Local Area Connection”.

1. Click the Start button, select

Settings, and select Control

Panel.

Page 9 / 26

CDMA 1xEV-DO Wireless Broadband Modem

AXW-D800 / AXW-D1900

- 9 -

Connecting the World Now

2. Double click the Network

Connection icon.

3. Go to Local Area

Connection Properties.

Page 10 / 26

CDMA 1xEV-DO Wireless Broadband Modem

AXW-D800 / AXW-D1900

- 10 -

Connecting the World Now

4. Select the “Internet Protocol

(TCP/IP)”

If there is no TCP/IP line

listed, you will need to

install TCP/IP first.

5. Press the “Properties”

button.

6. Check “Obtain an IP

address automatically”

7. Check “Obtain DNS Server

address automatically”.

8. Click Ok to exit Properties.

9. If asked to re-start the PC,

click “YES”.

Rate

Popular Axesstel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share