1. Home
    2. /
  2. Manuals
    3. /
  3. Atlantis-Land
    4. /
  4. A01-AE1-GX01
    5. /
  5. 6
Page 26 / 36 Scroll up to view Page 21 - 25
ENGLISH
27
such as interactive gaming, video streaming and real-time
audio much easier and faster than ever.
•
Plug’n’Play Installation:
The WebRunner supports up to 64
pre-defined PVCs and can automaticallydetect and select
the active VPI/VCI from the pre-defined list after ADSL line is
synchronized. It is plug-and-play.
1.4 Before Installing
Make sure that you have all you need to install the WebRunner.
You
should have the following:
•
A PC that has a NIC and TCP/IP stack correctly installed
•
An ADSL contract
•
A PPPoE stack (integrated in Windows XP and VISTA)
•
Intel® Pentium®III 600Mhz or compatible processor with
128MB RAM with CDRom drive
1.5 The Front Panel LEDs
Page 27 / 36
ENGLISH
28
LED
MEANING
PWR
Lit when power ON.
SYS
Lit when system is ready.
SYS
Lit when connected to Ethernet device
Green for 100Mbps; Orange for 10Mbps
Blinking when data transmit/received.
ADSL
Lit when successfully connected to an ADSL DSLAM.
1.6 The Rear Ports
PORT
MEANING
ADSL
Connect the supplied RJ-11 (“telephone”)
cable to this port when connecting to the
ADSL/telephone network.
Page 28 / 36
ENGLISH
29
LAN
Connect a UTP Ethernet cable (Cat-5 or Cat-
5e) to the LAN ports when connecting to a PC
or an office/home network of 10Mbps or
100Mbps.
RESET
After the device is powered on, press it to
reset the device or restore to factory default
settings.
0-3 seconds:
reset the device
6 seconds above:
restore to factory default
settings.
POWER
Connect the supplied power adapter to this
jack.
1.7 Information from ISP
WebRunnervwill scan automatically DSL Line for ADSL line
parameters and choose correct PVC’s profile from its pre-definited
profile. To configure your PPPoE connection, it is necessary to have
Username
and
Password
for your DSL account and make sure that
it is configured in PPPoE with LLC encapsulation.
1.8 Cabling
Please refer to the following instructions for installation procedures:
•
Connect your ADLS line to the RJ-11 jack labeled
ADSL
on
the back of the WebRunner.
•
Connect the CAT5/LAN cable to the jack labeled
LAN
on the
back of the WebRunner.
Connect the other end to the
Network card of your PC.
Ensure that all other devices connected to the same telephone line
as your Clipper (e.g. telephones, fax machines, analog modems)
have a line filter (
A01-AF2
) connected between them and the wall
socket (unless you are using a Central Splitter or Central Filter
Page 29 / 36
ENGLISH
30
installed by a qualified and licensed electrician), and ensure that all
line filters are correctly installed and the right way around.
1.9 Configuring a Internet Connection
We suggest to follow the instructions below to create an Internet
connection with WebRunner Ethernet:
1.9.1 For Windows Vista:
1.
Click
Start -> Control Panel -> Network and Sharing Center.
Page 30 / 36
ENGLISH
31
2.
Click on
Setup a connection or network.
3.
Select
Connect to the Internet.

Rate

3.5 / 5 based on 2 votes.

Popular Atlantis-Land Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top