Section 2, Engineering Guidelines

NetVanta 2000 Series System Manual

26

© 2002 ADTRAN, Inc.

61200361L1-1E

61200361L1-1E

© 2002 ADTRAN, Inc.

27

NETWORK TURNUP PROCEDURE

C

ONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Unpack and Inspect the SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Contents of ADTRAN Shipments - NetVanta 2100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

Contents of ADTRAN Shipments -

NetVanta 2300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

Supplying Power to the Unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

NetVanta 2100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

NetVanta 2300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

Installing NetVanta 2000 series Management Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Browsing Hosts Running Microsoft Windows NT, Windows 2000, or Windows 98/95 . . . . . . . .

28

Browsing Hosts Running POSIX-Compliant UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28

Section 3, Network Turnup Procedure

NetVanta 2000 Series System Manual

28

© 2002 ADTRAN, Inc.

61200361L1-1E

1.

INTRODUCTION

This section discusses the installation process of the NetVanta 2000 series systems.

2.

TOOLS REQUIRED

The tools required for installation of the NetVanta 2000 series systems are:

•

CATV-UTP Ethernet cable to connect the unit to the existing network

•

An Internet browser for configuring the unit

3.

UNPACK AND INSPECT THE SYSTEM

Each NetVanta 2000 series unit is shipped in its own cardboard shipping carton. Open each carton

carefully and avoid deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in

transit, immediately file a claim with the carrier, then contact ADTRAN Customer Service (see

Customer

Service, Product Support Information, and Training

in the front of this manual).

Contents of ADTRAN Shipments - NetVanta 2050 and 2100

Your ADTRAN shipment includes the following items:

•

The NetVanta 2050 or 2100 Unit

•

The NetVanta 2000 series

User Manual

CD (ADTRAN P/N 3253041)

•

AC Power supply - (ADTRAN P/N 336012 VUR01)

•

Crossover Ethernet cable for connecting the NetVanta 2100 directly to a PC

(ADTRAN P/N 8125M012)

Contents of ADTRAN Shipments -

NetVanta 2300 and 2400

Your ADTRAN shipment includes the following items:

•

The NetVanta 2300 or 2400 Unit

•

The NetVanta 2000 series

User Manual

CD (ADTRAN P/N 3253041)

•

AC Power cable (ADTRAN P/N 3127009)

•

(2) Brackets for installing the unit in a rackmount configuration (ADTRAN P/N 3265479)

To prevent electrical shock, do not install equipment in a wet location or during a

lightning storm.

NetVanta 2000 Series System Manual

Section 3, Network Turnup Procedure

61200361L1-1E

© 2002 ADTRAN, Inc.

29

4.

SUPPLYING POWER TO THE UNIT

NetVanta 2050 and 2100

The AC powered NetVanta 2050 and 2100 come equipped with a detachable 12 VDC at 800 mA

wallmount power supply for connecting to a grounded power receptacle. As shipped, the NetVanta 2050

and 2100 are set to factory default conditions. After installing the unit, the NetVanta 2050 and 2100 are

ready for power-up. To power-up the unit, connect the unit to an appropriate power source.

NetVanta 2300 and 2400

The AC powered NetVanta 2300 adn 2400 come equipped with an auto-sensing 100-240 VAC, 50-60 Hz

power supply for connecting to a grounded power receptacle. A grounded three plug detachable cable is

included with the shipment. As shipped, the NetVanta 2300 and 2400 are set to factory default conditions.

After installing the unit, the NetVanta 2300 and 2400 are ready for power-up. To power-up the unit,

connect the unit to an appropriate power source.

5.

INSTALLING NETVANTA 2000 SERIES MANAGEMENT COMPONENTS

Configuring the NetVanta 2000 series unit through the web interface requires a host computer with an

Ethernet interface and a web browser. ADTRAN recommends using Internet Explorer 5.0 or greater for

optimal viewing of configuration web pages.

The NetVanta 2000 series of products contains a default IP address of 10.10.10.1 and a netmask of

255.255.255.0. Select an IP address in the same range as the NetVanta unit and assign it to the host

computer running the web browser. An example IP address is 10.10.10.10 with a subnet mask of

255.255.255.0. This section contains detailed procedures for assigning the selected IP address to a host

computer for each of the popular operating systems.

•

This unit shall be installed in accordance with Article 400 and 364.8 of the NEC NFPA

70 when installed outside of a Restricted Access Location (i.e., central office, behind a

locked door, service personnel only area).

•

Power to the NetVanta 2050/2100 AC system must be from a grounded 90-130 VAC,

50/60 Hz source.

•

The power receptacle uses double-pole, neutral fusing.

•

Maximum recommended ambient operating temperature is 45

o

C.

•

This unit shall be installed in accordance with Article 400 and 364.8 of the NEC NFPA

70 when installed outside of a Restricted Access Location (i.e., central office, behind a

locked door, service personnel only area).

•

Power to the NetVanta 2300/2400 AC system must be from a grounded 100-240 VAC,

50/60 Hz source.

•

The power receptacle uses double-pole, neutral fusing.

•

Maximum recommended ambient operating temperature is 45

o

C.

Section 3, Network Turnup Procedure

NetVanta 2000 Series System Manual

30

© 2002 ADTRAN, Inc.

61200361L1-1E

Browsing Hosts Running Microsoft Windows NT, Windows 2000, or Windows 98/95

1.

Follow the menu path

S

TART

>S

ETTINGS

>C

ONTROL

P

ANEL

.

2.

After the

C

ONTROL

P

ANEL

appears, double-click the

N

ETWORK

icon to display the existing network

configuration.

3.

Select

TCP/IP

from the list of installed network components. If there are multiple sessions, select

the one for the Ethernet card in the host computer.

4.

Click

P

ROPERTIES

, which shows the existing properties of the TCP/IP protocol running on the host

computer in a multi-paned window.

5.

Select the

IP A

DDRESS

pane by clicking on it.

6.

Check the

S

PECIFY

AN

IP A

DDRESS

radio button.

7.

Enter the

IP A

DDRESS

as: 10.10.10.50 and

S

UBNET

M

ASK

as: 255.255.255.0.

8.

Click

OK

to close the properties window.

9.

Click

OK

on the network configuration window, which will ask you to reboot the browser

computer.

10. Click

Y

ES

to reboot your computer.

Browsing Hosts Running POSIX-Compliant UNIX

1.

Log in as

root

, or change to

superuser

.

2.

Run the

ifconfig

command

-a

option to list the configured network interfaces in the system. This

will show the Ethernet interface name as well. For example:

#ifconfig -a

lo0: flags=863<UP,LOOPBACK,RUNNING,MULTICAST> mtu 8232 inet 127.0.0.1 netmask

ff000000

hme0: flags=863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST> mtu 1500

inet 192.103.55.186 netmask ffffff00 broadcast 192.103.255.255

If you have a PC with DHCP client capabilities enabled, connect the NetVanta 2000 series

unit directly to your computer using the supplied ethernet crossover cable and follow the

procedure in DLP-1, Connecting to the Netvanta 2000 Series to connect for the first time.

The NetVanta 2000 series products have a DHCP Server capabilities enabled by

default. Connecting the unit to a network with a functioning DHCP server can cause

IP address assignment conflicts.

For any operating system not discussed in this section, refer to the system’s user

documentation for instructions on assigning IP addresses.