PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

Introduction

OGU 930500275-A1

9

REAR PANEL

The rear panel of the Router contains a reset button, a power adapter socket,

four LAN ports, one port, one USB device port,

††

two USB Host port, one FXO

port

‡‡

, two FXS ports and one Wi-Fi REG button.

Do not force the antenna beyond its mechanical stops. Rotating the antenna further may cause dam-

age.

FIGURE 4.

Rear Panel Ports

TABLE 3.

Port Description

PORT

DESCRIPTION

A

Phone DSL connector (2/2+)

B

port Four Ethernet ports 10/100 Mbps

C

ports USB 2.0 Host ports

D

FXS

E

Power connector

F

Power button

-

Reset to factory default button (located on the side of the device)

Optional

FXO

††

This port may be optional depending on the product version.

‡‡

This port may be optional depending on the product version.

PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

10

OGU 930500275-A1

Introduction

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

Hardware Installation

OGU 930500275-A1

11

Hardware

Installation

INTRODUCTION

This chapter will guide you through a basic installation of the Router including:

1.

Positioning the

PRG AV4202N

2.

Installing Micro Filters

3.

Connecting the Router to your network

4.

Setting up your computer for networking with the Router

Please read carefully the Safety Information in Appendix “A”

POSITIONING THE ROUTER

You should place the Router in such a location to ensure that:



It is located near an electrical outlet and a phone wall socket



Water or moisture cannot enter the case of the unit



It is out of direct sunlight and away from sources of heat



The cabling is away from power lines, fluorescent lighting fixtures, and

sources of electrical noise such as radios, transmitters and broadband am-

plifiers.



It is centrally located with respect to the wireless devices that will be con-

nected to the Router. A suitable location might be on top of a high shelf to

ensure the maximum coverage for all connected devices.

PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

12

OGU 930500275-A1

Hardware Installation

INSTALLING MICRO

FILTERS

Before beginning installation you must locate devices in your house requiring a

DSL filter such as phones, fax machines, answering machines, dial-up mo-

dems, Satellite TV dialers or monitored security systems and attach a DSL filter

to any one of them sharing the same phone line as your DSL modem.

To install DSL filters please follow these steps:

1.

Disconnect the phone cable from the telephone wall socket

2.

Insert the phone cable into the DSL filter port identified with a phone symbol

3.

Insert the DSL filter cable into the telephone wall socket

You do not need to attach a DSL filter to unused wall sockets.

FIGURE 1.

Micro Filter Installation

1

3

2

PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

Hardware Installation

OGU 930500275-A1

13

POWERING UP THE

ROUTER

To power up the Router:

1.

Plug the power adapter into the power adapter port located on the rear of

the Router

2.

Plug the power adapter into a standard electrical wall socket

3.

Press the Power button located on the rear panel of the Router

4.

Wait for the power LED to turn steady green

CONNECTING THE

ROUTER

The first step to install the router is to physically connect it to the telephone

socket and then to connect it to a computer by means of an Ethernet or an USB

connection.

To connect the phone cable:

1.

Connect one end of the phone cable into the DSL filter port identified with a

computer symbol

2.

Connect the other end of the phone cable into the DSL port on the rear of

the Router

FIGURE 2.

Phone Cable Connection

To connect the Ethernet cable: