PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

34

OGU 930500275-A1

Installation Wizard Section

FIGURE 4.

Wireless Setup Panel

VOIP SETUP

This page enables you to configure a VoIP account.

INSTALLATION

COMPLETED

This screen provides a summary of all the above Internet connection configura-

tion steps and their results. Click

Finish

to complete the wizard procedure.

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

Quick Setup Section

OGU 930500275-A1

35

Quick Setup

Section

This chapter will describe the

Quick Setup Section

accessible from the

Home

Page

of the

PRG AV4202N

upon user authentication to the Router.

Be aware that any configuration changes could compromise your connectivity.

When subscribing to a broadband service, you should be aware of the method

by which you are connected to the Internet. Your physical WAN device can be

either Ethernet, DSL, or both. Technical information regarding the properties of

your Internet connection should be provided by your Internet Service Provider

(ISP). For example, your ISP should inform you whether you are connected to

the Internet using a static or dynamic IP address, or what protocols, such as

PPTP or PPPoE, you will be using to communicate over the Internet.

The Router will automatically recognize if you have more than one physical

WAN device on your gateway, and will provide a configuration section for each,

under the 'Internet Connections' section of the 'Quick Setup' screen.

Your WAN connection(s) can be configured using one of the following methods.

Read the configuration instructions relevant to you, by selecting your connection

method from the list below:

1.

Point-to-point protocol over Ethernet (PPPoE) over ATM

2.

Point-to-point protocol over Ethernet (PPPoE) over PTM

3.

Point-to-point protocol over ATM (PPPoA)

4.

Routed Ethernet Connection over ATM (ETHoA)

5.

Bridged Ethernet Connection over ATM (ETHoA)

PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

36

OGU 930500275-A1

Quick Setup Section

6.

No Internet connection

FIGURE 1.

Quick Setup Panel

POINT-TO-POINT

PROTOCOL OVER

ETHERNET (PPPOE) OVER

ATM

To configure the Point-to-point protocol over Ethernet, follow these steps:

7.

Select 'Point-to-point protocol over Ethernet (PPPoE)' from the 'Connection

Type' combo-box.

8.

Your Internet Service Provider (ISP) should provide you with the Login user

name and Login password.

9.

If your board features a DSL connection, you will see an 'Automatic PVC

Scan' check box. Select this check box to enable the automatic configuration

of the VPI, VCI and encapsulation parameters (relevant to DSL connec-

tions).

ETHERNET (PPPOE) OVER

PTM

To configure the Point-to-point protocol over Ethernet, follow these steps:

PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

Quick Setup Section

OGU 930500275-A1

37

1.

Select 'Point-to-point protocol over Ethernet (PPPoE)' from the 'Connection

Type' combo-box.

2.

Your Internet Service Provider (ISP) should provide you with the Login user

name and Login password.

POINT-TO-POINT

PROTOCOL OVER ATM

(PPPOA)

To configure the Point-to-point protocol over ATM, follow these steps:

1.

Select 'Point-to-point protocol over ATM (PPPoA)' from the 'Connection

Type' combo-box

2.

Your Internet Service Provider (ISP) should provide you with the following in-

formation:

- Login user name

- Login password

3.

By default, the 'Automatic PVC Scan' check box is enabled, which means

that the Router configures the VPI, VCI and encapsulation parameters

automatically. If you would like to configure these parameters manually, un-

check this check box.

- Specify the VPI and VCI values.

- Select the encapsulation method from the combo-box. You can choose

among the following methods: LLC, VCMux and VCMux - HDLC

ROUTED ETHERNET

CONNECTION OVER ATM

(ETHOA)

To configure the Routed Ethernet connection over ATM, follow these steps:

4.

Select 'Routed Ethernet Connection over ATM (ETHoA)' from the 'Connec-

tion Type' combo-box

5.

Your Internet Service Provider (ISP) should provide you with the following in-

formation:

- Specify the value of the VPI and VCI parameters.

- Select the encapsulation method from the combo-box. You can choose

among the following methods: LLC, VCMux.

- Select the Internet Protocol: Most Internet Service Providers (ISPs) provide

dynamic IP addresses, hence the default "Obtain an IP Address Automati-

cally". Should this not be the case, select the "Use the Following IP Address"

option. The screen will refresh. Enter the IP Address, Subnet Mask, Default

Gateway, and DNS Server details provided to you by your ISP.

ROUTED ETHERNET

CONNECTION OVER PTM

(ETHOP)

To configure the Routed Ethernet connection over PTM, follow these steps:

1.

Select 'Routed Ethernet Connection over PTM (ETHoP)' from the 'Connec-

tion Type' combo-box

PRG AV4202N

© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

38

OGU 930500275-A1

Quick Setup Section

2.

Your Internet Service Provider (ISP) should provide you with the following in-

formation:

- Select the Internet Protocol: Most Internet Service Providers (ISPs) provide

dynamic IP addresses, hence the default "Obtain an IP Address Automati-

cally". Should this not be the case, select the "Use the Following IP Address"

option. The screen will refresh. Enter the IP Address, Subnet Mask, Default

Gateway, and DNS Server details provided to you by your ISP.

BRIDGED ETHERNET

CONNECTION OVER ATM

(ETHOA)

To configure the Bridged Ethernet Connection over ATM (ETHoA), follow these

steps:

1.

Select 'Bridged Ethernet Connection over ATM (ETHoA)' from the 'Connec-

tion Type' combo-box

2.

Your Internet Service Provider (ISP) should provide you with the following in-

formation:

- Specify the value of the VPI and VCI parameters.

- Select the encapsulation method from the combo-box. You can choose

among the following methods: LLC, VCMux

BRIDGED ETHERNET

CONNECTION OVER PTM

(ETHOP)

To configure the Bridged Ethernet Connection over ATM (ETHoA), follow these

steps:

1.

Select 'Bridged Ethernet Connection over ATM (ETHoA)' from the 'Connec-

tion Type' combo-box

NO INTERNET

CONNECTION

Select 'No Internet Connection' from the 'Connection Type' combo-box. Choose

this connection type if you do not have an Internet connection, or if you want to

disable all existing connections.

WIRELESS

Click the 'Enabled' check box to enable your wireless connection. Specify the

wireless network's ID in the 'SSID' field. The default SSID is 'openrg'.

ADMINISTRATOR

In this section it is necessary to specify the administrator's e-mail in the 'E-mail'

field. System alerts and notifications are sent to this address.